HW A Solid Steel bar of dlameter 6omm andlengtj2.350mmis p laced inside analuminum cylinderof Insiediameter Fommm and out side dlameter lomm,a compressive load of loo0 law is applled on the assembi nfind the stresses in the barand the cylinder? take eEst= 200GPA and EAl= FoGla-SAL?D=u.25%DলিCover Plate0.25mmdi350mmA lum. cylinderSteel bar

Answered: Image /qna-images/answer/da136ba9-bfde-4daa-9781-3ec86d387330.jpg

H.WD A Solid steel barr of dlameter 6omm andHengtip 2. 350mmis Placed inside analuminum cylinder of Inside - dlameter Femm and out side dlameter llamm, a compressive load of loon la is applled on the assembe find the stresses in the bar dnd the cylinder? take e Est= 200G Pa and EAl= FoGla. SAL?A=0.25 tover Plate 0.25mm di 35omm A lum. cylinder steel bar

H.WD A Solid steel barr of dlameter 6omm andHengtip 2. 350mmis Placed inside analuminum cylinder of Inside - dlameter Femm and out side dlameter llamm, a compressive load of loon la is applled on the assembe find the stresses in the bar dnd the cylinder? take e Est= 200G Pa and EAl= FoGla. SAL?A=0.25 tover Plate 0.25mm di 35omm A lum. cylinder steel bar

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

dae 11.25 kips st steel ∙Alum in um A fully bonded aluminum Outer shell and Steel inner core bar is axially loaded. Find the ✓1.25 kips normal stress for the alum', num outer shell. Answer in ksi Given: EA = 11,000 ksi Al Est = 29,000 ks; XAL = 13.5 x 10-6 Y OF Xst = 6.5 x 10-6 1/F dAl = 1.0 in. dst = 0.25 in. AT = 65 °F
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
pon 9.18 A steel rodin. in diameter and 25 ft long is subjected to an ace axial tensile load of 15,000 lb. Compute (a) stress ons Lanogsib & new (b) strain (c) total elongation aaste sviesiqmos srit nimmst gaites 900 viss srit .rwoda al
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
Derive the maximum steel ratio and the recommended rteel ratio fe' O.856 fy Po-004 3 0.85 fc' pooos= 0-85
Hw A shaft comB Sed nf Seymeats Ac,cD and DB is fastened to rigid suprorts and looded as shown, for steel G=83 GNIM, for Amminum G=28GN/m? and for bronze G: 35 GNIM Determine the maximum shcaring Stress oleve lored in ench Segment? Ans: To=472Nim, Tal=s go Aluminum Bronze d=25 Steel d=25mm d= Semm 1.5 m 2m Im مرّر ل لأعلى لاستعراض الفلاتر إضافة شرح. . . mum
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
7 Enercise:- 30 long with is subjected to a Assuming deformation is entirely elastic and manimum allowable elongation tensile 30000y that the is 0.3 mm while manimum. allowable reduction in, digmeter is 0.015mm. choose amory below only. candidate meeting requirent E (GPa) A cylindrical rod 100 mm diameter of 12 mm load of 30000 N. Aluminium alloy Bronze Titanium allow 70 100 110 U(Poiss ons vahi) 0.33 0.34 0.3
* TRUTT 50 kN/m 8m TIZI SLAB THICKNESS 150mm 2500 mm fe'= 21 MPa fy = 414 тра Cc = 40mm spacer barp=25mm Say bw= 0.6h DESIGN THE T-BEAM AND SHOW THAT TENSION STEEL YIELDS AND THE BEAM IS TENSION CONTROLLED
The eye bolt is used to support the load of 5 kip. Determine its diameter d to the nearest 1/8 in and the required thickness h to the nearest 1/8 in of the support so that the washer will not penetrate or shear through it. The allowable normal stress for the bolt is σallow = 21ksi and the allowable shear stress for the supporting material is Tallow=5 ksi. Show the FBD and solution
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa