Graph:Take a graph sheet and divide it into 4 equal parts. Mark origin at the center of the graph sheet.Now mark +ve X-axis as Vf, -ve X-axis as Vr, +ve Y-axis as Ifand –ve Y-axis as Ir.Mark the readings tabulated for Si forward biased condition in first Quadrant and Si reverse biased condition in third Quadrant. Fig: V-I Characteristics of PN Junction Diode underForward & Reverse Bias ConditionsV.Ve Forward Bias Condition:Reverse Bias Condition:Table 1.3Forward VoltageAcross theDiode,Vr (Volts)Table 1.4ForwardReverse Voltage Reverse Currentthrough theDiode,VoltageCurrent throughthe Diode,G(mA)VoltagesourceAcross thesourceDiode,V3 (Volts)Vs (Volts)Ve (Volts)k (YA)0.10.1000.000194110.1110.20.1990.00147120.2220.30.2910.0088732.9990.40.3640.0366.5.9990.50.4110.0891211.9980.60.4400.1601514.9980.70.4610.23910.5000.50020.5551.4456.0.6235.377120.66111150.67414200.68919

According to the question, for the given data as shown below We need to plot the V-I…

Graph: Take a graph sheet and divide it into 4 equal parts. Mark origin at the center of the graph sheet. Now mark +ve X-axis as Vf, -ve X-axis as Vr, +ve Y-axis as Ifand –ve Y-axis as Ir. Mark the readings tabulated for Si forward biased condition in first Quadrant and Si reverse biased condition in third Quadrant.

Graph: Take a graph sheet and divide it into 4 equal parts. Mark origin at the center of the graph sheet. Now mark +ve X-axis as Vf, -ve X-axis as Vr, +ve Y-axis as Ifand –ve Y-axis as Ir. Mark the readings tabulated for Si forward biased condition in first Quadrant and Si reverse biased condition in third Quadrant.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
What is the difference between a diode and rectifier?
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
Sketch i agains v to scale for the circuit. Assume 0.6 V for all diodes in the forward-bias region.
In the reverse-bias region the saturation current of a silicon diode is about 0.1 A (T 20°C).Determine its approximate value if the temperature is increased to 50°C.
The voltage drop of schottky diode is more than that of power diode? true or fales
The o/p voltage of a quadrupler is 540 V What min. PIV rating must each diode have?
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
05: [insert description] Assume 0.6 V for all diodes if forward bais, reverse breakdown voltages are given, sketch IV curves for circuits. Given: ZA 6.8 V (a) (b) I DA (c) 5.6 V 5.6 V
For the diodes used , at what Voltage (VD) does condection stars .
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.