From Figure 3, write node-voltage equations: one for each inputa.terminal of the op amp.b. The expression for the load current (i.) can be written as a function of the inputvoltage (V) and the load voltage (v.)iz = Avin + Bv,b.1.What is the expression for A?What should be the condition for R, R, R, and R4, so that B isb.2.zero? (NB: this condition will make i, depend only on v, and not on R.)R4R3OA1R2R1RLVinVLiLFigure 3

Answered: Image /qna-images/answer/2d3c13a1-14c7-4c5f-be12-bd765cc85b69.jpg

From Figure 3, write node-voltage equations: one for each input terminal of the op amp. o. The expression for the load current (i,) can be written as a function of the input voltage (vm) and the load voltage (v,) i, = Av, + Bv, b.1. What is the expression for A? b.2. What should be the condition for R,, R, R, and R, so that B is zero? (NB: this condition will make i, depend only on v, and not on R.) R4 R3 OA1 R2 R1 Vin RL Figure 3

From Figure 3, write node-voltage equations: one for each input terminal of the op amp. o. The expression for the load current (i,) can be written as a function of the input voltage (vm) and the load voltage (v,) i, = Av, + Bv, b.1. What is the expression for A? b.2. What should be the condition for R,, R, R, and R, so that B is zero? (NB: this condition will make i, depend only on v, and not on R.) R4 R3 OA1 R2 R1 Vin RL Figure 3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An inverting op amp has Rf= 600kohm and R1= 6kohm. Determine the op amp circuit voltage gain, input resistance and output resistance. Also Determine the output voltage and input current if the input voltage is 0.1 V. Assume op amp to be ideal one.
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
One way to measure the slew-rate limitation of an op amp is to apply a sine wave (or square wave) as the input to an amplifier and then increase the frequency until the output waveform becomes triangular. Suppose that a 1-MHz input signal produces a triangular output waveform having a peak-to-peak amplitude of 4 V. Determine the slew rate of the op amp.
3. A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing the corresponding circuit and by explaining your answer or presenting the solution. a. If VA-0, VB-1V, RA-RB-10kQ, R1=70kQ, R2=00 and vout-8V, which terminal (A or B) is the noninverting input? b. If VA-10, VB=0V and B is the inverting input, select RA, RB, R1, and R2 and to obtain an output voltage of 20V. c. If VA=VB=1V, R1=0, R2=∞ and Vout=1V, which terminal (A or B) is the inverting input? R2 VA RA OVout RB B VB R1
Semi-ideal OpAmps – If we have an opamp with FINITE gain A, solve for the voltage gain Vout/Vin. Recall that the semi- ideal op-amp (finite gain) has the equation, Vout = A(V*-V) No current flows into V* and V. RS 7 Vin Vout OUT R1 6 R2
Here is a single op-amp, shown under two different conditions (different input voltages). Determine the voltage gain of this op-amp, given the conditions shown. Also, write a mathematical formula solving for differential voltage gain (AV) in terms of an op-amp's input and output voltages. +12 V +12 V Va=1.00 V %3D Vout = 1.5 V +12 V V=1.00003 V %3D -12 V +12 V +12 V Va =1.00 V %3D Vet = 6.8 V +12 V V 1.00004 V -12 V
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)
2)For the following circuit, assuming the Op-Amp is ideal, fill in the table for the missing values when vi = 2V, 12 10 k [mA] [mA] [mA] [mA] ...... I kn lo I2 ...... IL Io o vo vi ........
By using only two op-amps, design a circuit that can perform the following operation: Vo == Also, evaluate the given circuit equation. Show all the assumptions, calculation and the circuit illustration. Marking Scheme: Circuit Design Assumptions Calculation