Answered: For the given circuit calculate the…

For the given circuit calculate the maximum power that can be transferred from the circuit to the load impedance ZL. 1220° V -j102 a -j2 A 10 2SV. 2V. ZL b

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Related questions

Q: 3 ohm 25,47 mH 4 Ohm ZL 6,37 mH 240Cos(314t+30) 398UF Find the load impedance (ZL) for the maximum…

A: For dc source the maximum power transfer states that maximum power is abstract by load resistance if…

Q: Q2/ find the load impedance ZL that absorbs the maximum average power. Calculate that maximum…

A: Zth =5∥ 8-J4×J10 =3.415+J0.7317Ω ZL=Zth=3.415+ J0.7317

Q: 2. Three impedances Za , Zb and Zc are connected in parallel. If at 60 hz , Za = 3 + j4 , Zb = 4 –…

Q: For the circuit in the figure, Rab =6002, Zbc = 8022+ j6022. Compute the following: a. Phase and…

Q: The circuit shown consists of a source driving a load that consists of the parallel connection of…

A: The circuit diagram is shown below: a) The complex power of the load A is given by the expression…

Q: For the following circuit, find (a) the load impedance required for maximum average power transfer…

Q: Connected to ab terminals in the given circuit ZL=(1AC-J2D)O wwww wwwwm the power that the impedance…

A: For thevenin voltage open circuit the load terminals. The circuit will look like

Q: a) Determine the load impedance for the circuit that will result in maximum average power being…

Q: 1. From the given circuit, take V₁ = 240, ZL = currents. Determine also the total complex power from…

A: Given A delta -Delta connected circuit.we need to determine the line and phase currents and the…

Q: Given V 120/220° V. ZL = 2- j2 2, and Z 8+ j8 2 for a balanced three-phase wye-wye an = circuit with…

A: Given system is balanced, so use per phase analysis to find current phase b. Given phase sequence…

Q: 1. From the given circuit, take V₁ = 240, Z₁ = 20 - j3 ohms. Find the phase currents and line…

A: In this question, We need to determine the phase current, line current and complex power? We know…

Q: Problem 3 Find the load impedance Z₁ that would absorb the maximum power. Va $D 1|2 + www 452 ZL 852…

Q: IF Z=R+jX and I solve for impedance with Z=V/I with a complex number of 28.57+13.835j Does that…

A: Yes, that is what it exactly means.

Q: Given a parallel impedance and resistor with a source emf of 220V, ZR =1020° 2, Z = 4 + j3, and…

A: Power factor is the cos (impedance angle) We will find total impedance by combining the three…

Q: A wye-connected load with ZA = 12 + j12 Q, ZB = 15 + j 20 Q and Zc = 10 Q is connected to a…

A: In this question, We need to determine the power factor of the given system? Power factor =…

Q: Q2: If Z = - j 2Ω, find V, in the circuit using nodal analysis. 12230V +V, +V 2 2260 + j1Ω jin 0…

A: 2) To find the value of VL using nodal analysis

Q: Two impedances Z1 = 2 + j4 and Z2 = R + j0 are connected in parallel. Determine R so that the power…

A: First calculate impedance of the two parallel connected elements and than find impedance angle . Now…

Q: From the given circuit, take V₁ = 240, Z₁ = 20 - j3 ohms. Find the phase currents and line ZL…

A: In this question, A 3phase balance source supply to 3 phase balance load. We need to find the…

Q: P 12.3-7 A balanced Y-Y circuit is shown in Figure P 12.3-7. Find the average power delivered to the…

A: It is given that:

Q: Determine the complex power transmitted to the three-phase load of a four-wire Y-Y circuit like the…

A: Here source and load are balanced , we can use per phase analysis. we will apply KVL in the three…

Q: Please ASAP all answers are wrong in previous...Find ZL for maximum ave. power transfer (ac) and…

A: Thevenin voltage is the voltage at ZL terminals with ZL is open circuit. Thevenin impedance is the…

Q: Given v = 30 cos(wt – 60°) V and i = 3 cos(wt + 30°) A for the load impedance shown, what is the…

Q: Q2/ find the load impedance ZL that absorbs the maximum average power. Calculate that maximum…

A: zth = 5 ||8-j4+j10= 5 8+ j6= 3415+ jo 731713+j6for max average power zl = zth = 3415+ jo.…

Q: Q5: For the circuit in the figure, Determine the complex power delivered to the three-phase load.…

Q: 4. In the single power system to the right, find the complex power S supplied by the Zc = - j0.2 Z =…

A: To find the complex power S supplied by the source

Q: Two impedances are fed by a source with V = 100Vrms 160 °, as shown below. The total current is I =…

A: In this question we will find currents, impedances ,power factor....

Q: 4Ω ww- ell Determine the load impedance that z, maximizes the average power drawn from the circuit.…

A: For dc source the maximum power transfer states that maximum power is abstract by load resistance if…

Q: Find the power to be consumed by the impedance of ZL = (157-J28) N connected to the ab terminals in…

A: According to the Thevenin theorem, A linear bilateral planer network that contains one or more…

Q: Example: For the circuit shown below, Determine the total average power, reactive power, and complex…

A: As the system is perfectly balanced, we can solve the problem easily using per phase analysis.…

Q: Consider the following three phase balanced circuit. 21020° Vrms J0.5 2 24- 21 2 |2102-120° Vrms…

A: Here, we have given a three phase balanced circuit. We have to calculate the average dissipated…

Q: The two impedances shown below are connected in parallel. The combination draws 2+j1 A current from…

Q: 12.57 Determine the line currents of the three-phase circuit in the figure. /-120°, V. = 110/120° V.…

A: The solution can be achieved as follows.

Q: Given v = 75 cos(wt + 30°) V and i = 5 cos(wt - 15°) A for the load impedance shown, what is the…

Q: Find: The real, reactive and apparent power at the load Power factor at the source and load side Z,…

A: impedance, Z = ZR + ZC Z = 400 - j300 magnitude of (Z) = 4002+3002 = 500…

Q: Consider the following three phase balanced circuit. 21020° Vrms j0.5 N 24– j21 N 2102-120° Vrms…

A: Given: The given diagram is.

Q: If the impedance Z1 = 0 + j10 and the impedance Z2 = 10 - j10 are connected in parallel, the…

Q: For the given circuit calculate the maximum power that can be transferred from the circuit to the…

Q: given the circuit below, compute for the following a. Source phase voltages b. Source line voltages…

A: In this question, We need to determine the source phase voltage, source line voltages and line…

Q: Nodal Analysis: AC circuit Find the node voltages using nodal analysis from the following circuit mm…

Q: A single phase circuit is supplying the two loads, Load1 draws a real power of 350 kW at a unity…

A: Given: A single-phase circuit is supplying the two loads, Load 1 draws a real power of 350 kW at a…

Q: Given v = 75 cos(wt + 30°) V and i = 5 cos(wt - 15°) A for the load impedance shown, what is the…

A: In this question we will find complex power absorbed by load..

Q: H.W.(2): For the A-connected load in Figure, find the line voltages, phase currents and line…

Q: j202 + V2 10 Ω (10/3)I, + + O -j10/3 N V10/45° V Vị Zj102

Q: The phase voltages across a certain load are given as: Va = 176 – j132 volts Vb = -128 - j96 volts…

Q: 15. The Thevenin impedance of a network seen by the load terminal is 80 + j55 ohms. For maximum…

Q: Q3 (а) Given a circuit in Figure Q3(a); Determine the load impedance, Zı that results in maximum…

A: Maximum power transfer to ZL when Load impedance is equal to complex conjugate of thevinin…

Q: Three 230-V generators form a delta-connected source that is connected to a balanced delta-connected…

A: Use per phase analysis This is a very basic network with delta delta Use the given values

Q: -j2 n j4 N V3 20 V, ZL 4/0° V

Concept explainers

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.

Question

100%

Please, can you solve the question as soon as possible.

For the given circuit calculate the maximum power that can be transferred from the
circuit to the load impedance ZL.
1220° V
-j102
a
-j2 A
10 2SV.
2V.
ZL
b

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(a) Transform v(t)=75cos(377t15) to phasor form. Comment on whether =377 appears in your answer. (b) Transform V=5010 to instantaneous form. Assume that =377. (c) Add the two sinusoidal functions a(t) and b(t) of the same frequency given as follows: a(t)=A2cos(t+) and b(t)=B2cos(t+). Use phasor methods and obtain the resultant c(t). Does the resultant have the same frequency?
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
Desian aproblem for wye delta transform adions Determinc the eauivalend resistance between the terminals A andA B.
10 Ω m I₁ j4 Ω + I₂ ~ Vs E₁ || 2:1 The load on the right is absorbing 650 W -j200 VAR. V₁ = 80 / 0° V. + V₁ I
Three impedances, Z1 =10020.Q, Z2 =63.2518.43.2 and Z3 =1002-90•Q are connected in star. Convert the star to an equivalent delta connection. And draw the star network and also the equivalent of delta connection
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms