For the fluid system in Fig 6 construct the linear graph, identify the state variables, and derive the state equations. The output variables are the pressure p₁ and p2 at the tanks. C₁ ARA H I,R Q,(t) C₂ Figure 6: An fluid system R₂ V (t) ww Rs RL L V (t) Figure 7: A tuning circuit for radio

For the fluid system in Fig 6 construct the linear graph, identify the state variables, and derive the state equations. The output variables are the pressure p₁ and p2 at the tanks. C₁ ARA H I,R Q,(t) C₂ Figure 6: An fluid system R₂ V (t) ww Rs RL L V (t) Figure 7: A tuning circuit for radio

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

A series circuit consists of a resistor, a coil, and a capacitor connected across a 300 V, 60 Hz AC source. THe current drawn is 20A. The voltage across the resistor is 60 V, that across the coil is 260 V and that across the capacitor is 100V. The resultant voltage across the coil and the capacitor is 254.56 V. Determine (a) the resistance of the resistor, (b) the resistance and inductance of the coil, and (c) the resistance and capacitance of the capacitor.
Number 9 Please show your detailed solution. Number 9 Please show you detailed solution. A 50-ohm resistor is in series with a 40-?F capacitor across a constant potential source of 180 volts. Determine frequency that will give current of 3.13 amp. A. 250 Hz C. 160 Hz B. 200 Hz D. 140 Hz
1- For the values = 0.7 and W, = 2 find the rise time, peak time, settling time, and the maximum peak values. the
Please write the solution clearly
1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?
I. SOLVE THE FOLLONING PROBLENS : A COPPER WIRE OF 0,3 Mm RAAUS HAS A LEN ETH OF 1. JOM- IF THE RESISTIVITY of cOpPER IS 1-7 x0 WHAT WOULD BE THE RESISTANOE OF THE WIRE? OF A 100m WIRE IS 1035 mm AND 3.7 OHMS. WHAT 2. THE DIAMETER THE REISTANCE IS IS THE CONDUCTIVITY 3. WHAT WILL BE THE VALUE OF A CAPACITOR WHEN IT HAS A CAPACITIVE REACTANCE OF 300R ANP to A 6o HZ. SUPPLY? IN FARADS IS CONNECTED 4. WHAT Is THE VALUE OF THE RESISTOR WITH THE FOLLOWING COLORS ? A. BROWN, BLACK, GOLD, REP B. BLUE YELON BROWN, SILVER PED, SILVER, BROWN, VIOET C. 5. AND t WHEN V 220V AND R= 50n WHEN I = 45 A WHEN V = 120V FIND V ANO R 80n AND AND E= 11A-
1- In a buck DC/DC converter: ton V₁ = 100 V, R= 80, D ==0.8, f == 20000 Hz, L = 200 μH, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd - İd K C1 ww + Vo
capacitor having capacitance of 10uF is connected with 1k ohm resistor in series. The switch of the DC supply of 10 Volts, closes at t = 0. Compute the following a. Draw a circuit diagram for t- and t+ b. Compute the time constant c. Plot the Voltage with respect to time, showing the behavior of capacitor charging(take at least 10 values of time in seconds to draw a graph).
For the following circuit, do the following:a) Write the mathematical expressions for the voltage VC, VR1 and IC if the switch is on theposition 1.b) Find the voltage VC, VR1 and IC if the switch changes to a position 2 at t = 100ms.c) Determine the discharge time of the capacitor.d) Draw the charge and discharge waveforms.
1. What impedance vector 0 – j22 represents:A. A pure resistance.B. A pure inductance.C. A pure capacitance.D. An inductance combined with a resistance.
If the input voltage for the given circuit below is 220 V at 50 Hz, the load resistance (RL) is 3300 and the average output voltage is 20 V. Assume the diodes to be germanium diodes. Determine the turns ratio of the transformer used. If a capacitor of 100 µF is connected parallel to the load resistor (RL), Determine the ripple factor. D1 D2 V D3 .... D4 RL a. The turns ratio of transformer (Npri/Nsec) is b. The Ripple factor is cell rell
For the circuit below assuming an ideal switch, preform transient analysis to predict the voltage across resistor, R2 and plot the results. The inductor will have zero current as initial condition. L1 0.005 2 U1 100mH R1 1k V1 20Vdc R2 100