For the beam loaded as shown, solve the reactions, perform checking, write the shear and moment equations, determine its values and draw the shear and moment diagram. Show complete solutions in all answers. Answers without solutions will not be considered. Upload the photo of your answers in your respective google classroom on time. 2m R1 20 KN 40 KN/m 2m 4m 60 KN/m 4m R2

For the beam loaded as shown, solve the reactions, perform checking, write the shear and moment equations, determine its values and draw the shear and moment diagram. Show complete solutions in all answers. Answers without solutions will not be considered. Upload the photo of your answers in your respective google classroom on time. 2m R1 20 KN 40 KN/m 2m 4m 60 KN/m 4m R2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This question is a short free-response question. Show your work for each part of the question. A puck of mass m, slides across a horizontal surface and collides with a stationary, nonuniform rod that is pivoted about its left end in three configurations, as shown. In each case, the puck travels with the same initial velocity v, and collides with the rod at time te . In Case 1 the puck rebounds away from the rod, in Case 2 the puck comes to rest after the collision with the rod, and in Case 3 the puck sticks to the rod. Frictional effects between the rod, puck, and floor, as well as frictional effects of the pivot, are small enough to be considered negligible. Case Piyot Case 2 Pivot ---------------- Case 3 (a) On the graph below, sketch and label the two quantities as a function of time for Case 1. You do not need to calculate values for the y-axis, but the same vertical scale should be used for both quantities. i. Angular momentum of the puck ii. Angular momentum of the rod Label the…
The block at C is moving downward at vc = 3.2 ft/s . (Figure 1) Figure @AB 2 ft B 3 ft 30° 1 of 1 vc Part A Determine the angular velocity of bar AB at the instant shown. Express your answer to three significant figures and include the appropriate units. WAB = μA Value Submit Previous Answers Request Answer X Incorrect; Try Again Provide Feedback Units ?
Introduction Structural analysis is important for designing all type of structure including truss structure. There are several method to analyse truss structure. Therefore, student should be able to analyse the truss structure with appropriate method. This assignment is given to student to evaluate the ability of the student in solving the complex problem involving truss structure as shown in Figure 1 below. B 6m 88) O 20kN By using an appropriate method, i) 6m 20kN/m D 30KN Figure 1 6m H 20KN 6m LL G Figure 1 above shows a truss structure, which is supported at A and G. The truss is design to support a uniform load 20kN/m from C to E as shown in the figure. Given the elastic modulus, E=200GPa, and the cross-sectional area for member AJ, JI, IH, and HG is equal to 500mm² while other members is equal to 250mm². Based on the details given, solve the following task to analyse the truss structure. Task 1 8m Describe the determinacy and stability of the truss structure. Your answer must be…
The tire wrench shown in the accompanying figure is used to tighten the bolton a wheel. Given the information on the diagram, determine the moment about point O for the two loading situations shown:a. pushing perpendicular to the wrench armb. pushing at a 75° angle.
2hd Semester, SY 2021-2022 / College of Engineering / Bachelor of Science in Civil Engineering A freight train starts from rest and travels with a constant acceleration of 0.5 ft/s 2. After a time t' it maintains a constant speed so that when t = 160 s it has traveled 2000 ft. Determine the time t' and draw the v-t graph for the motion. Maximum file size: 50MB, maximum number of files: 1
A construction worker pulls a five-meter plank up the side of a building under construction by means of a rope tied to one end of the plank (see figure). Assume the opposite end of the plank follows a path perpendicular to the wall of the building and the worker pulls the rope at a rate of 0.26 meter per second. How fast is the end of the plank sliding along the ground when it is 1.2 meters from the wall of the building? (Round your answer to two decimal places.) 5m X m/sec
Express the moment of the couple acting on the pipe assembly in Cartesian vector form. (Figure 1) Express your answer in terms of the unit vectors iii_evec, jjj_evec, and kkk_evec. Use the 'vec' button to denote vectors in your answers. Express your answer using three significant figures. What is the magnitude of the couple moment?
Solve in 15 min
Two children are playing in the park on a seesaw mounted on a merry-go-round as shown in the figure below. The merry-go-round rotates about the ground-fixed (frame GG) vertical at \omega_{v}=ωv= 2.9 rad/sec, and at the instant shown the seesaw turns at \omega_{H}=ωH= 2.5 rad/sec relative to the merry-go-around JJ. \left(\hat{i},\hat{j},\hat{k}\right)(i^,j^,k^) are unit vectors fixed in the seesaw board BB. The children are each 5 ft from the fulcrum OO. The girl slides a stone PP along the see-saw board toward the boy. The velocity of the stone relative to the board is -4.4 \hat{j}j^ ft/sec at an instant when the stone is 2.3 ft from the girl and \theta=0 \degθ=0deg. Find the magnitude of the velocity of the stone PP relative to the ground GG, i.e., V_{P/G}VP/G, at this instant.
Write shear force and bending moment equations for the beams and sketch shear force and bending moment diagram for the following questions: 10KN SkN/m 2. 4 m 2 m
모 Presentation1 PowerPoint 9 Search 1 Ad 2. Design Transitions Animations Slide Show Review View Help a = 15.0 m/s 40. Figure P4.40 represents the w total acceleration of a particle moving clockwise . in a circle of radius 2.50 m at a certain instant of time. For that instant, find (a) the radial acceleration of the particle, (b) the speed of the particle, and (c) its tangen- 2.50 m 30.0° tial acceleration. Figure P4.40
O Quiz: Midterm Quiz 2 O Hooke's Law Calculator 103273/take Compute the deflection of a structural member made of aluminum if a load of 755 N is applied to the bar. The member has a uniform rectangular cross-section with dimensions of 6 mm x 100 mm, as shown in the accompanying figure. 44/14 // F = 755 N L = 250 MM