For the beam and point loadings shown below: Draw the shear force and bending moment diagrams for the beam and loading shown below. Determine the reactions at C and E. Draw the shear force and bending moment diagrams for the beam. Determine the maximum magnitudes for both the shear force and bending moment. 100 lb 100 lb A 15 in. C 20 in. 250 lb to D 25 in. E 10 in. B

For the beam and point loadings shown below: Draw the shear force and bending moment diagrams for the beam and loading shown below. Determine the reactions at C and E. Draw the shear force and bending moment diagrams for the beam. Determine the maximum magnitudes for both the shear force and bending moment. 100 lb 100 lb A 15 in. C 20 in. 250 lb to D 25 in. E 10 in. B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? -2.3 2.3 P 220 lb Answers: M- Ax i 1.8' 64 lb-ft lb .8'
A cantilever beam with length L carries a concentrated load of P at its free end. The beam is tapered with diameters of D at the support and d at the free end. The beam is to be analyzed considering flexure only. Which of the following expressions gives the distance from the free end where the beam will break? Select the correct response: Ld/[2(D-d)] Ld/[2(D+d)] LD/[2(D+d)] LD/[2(D-d)]
O 4 Question 7 of 15 ---x, m lb lb ^4) ENG
• Calculate the magnitude of the resultant support reaction at A. • Calculate the horizontal support reaction at A and B • Calculate the vertical support reaction at A and B Inclue 4 decimal points in all the answer.
Consider the beam shown in (Figure 1). The support at B can be assumed to be a roller. Suppose that w = 7 k/ft Figure 12 ft 12 ft < 1 of 1 Part A Determine the z and y components of reaction at A. Express your answers using three significant figures separated by a comma. [5] ΑΣΦ [. Az. Ay= Submit ▼ Part B Request Answer B₁ = Determine the y component of reaction at B. Express your answer using three significant figures. ΕΠΙ ΑΣΦ vec Pearson J1 vec 3 → ? ? k Revie
Q1/ Determine the magnitude and direction angle(0) of force (F4) So that the particle shown in figure (1) is in equilibrium? Fi-500 N F2=750 N 33 F4 30 60 F3=1200 N Figure (1)
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %3D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. 6 ft 3ft VAVAVAVAVA Ib f Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of (Igx) Vahue of ybar (9) Location of the Hydro. Force measured from the water surface of the gate inclined (yel Ib ft ***answer Hydrostatic Force Fon the box below: Answer: 1311.03 The correct answer is: 1022.1
Consider the frame shown in (Figure 1). Suppose that F = 750 N. Figure 2 m 3 m B 600 Nm 4 m 1 of 1 Part A Determine the reaction at roller A Express your answer to three significant figures and include the appropriate units. Ay = Submit Part B μA Value B₂, By = Submit Request Answer Determine the horizontal and vertical components of reaction at pin B. Express your answers in newtons to three significant figures separated by a comma. Units [V—| ΑΣΦ | ↓↑ vec Request Answer < Return to Assignment ? Provide Feedback wwwww ? N
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 210 N and the couple M = 527 Nm. 90 N 250 mm 150 N 400 mm M&N•m A 300 P
! Required information Consider the following figure. 10 in.. EQ P F B 4 in. lb lb ↑ C D 5 in. 5 in. Determine the components of the reactions at A and B if the load P= 240 lb is applied as shown. The components of the reaction at A are: Ax= lb ← Ay= lb ↑ The components of the reaction at Bare: Bx= By=
• What is the member force in CD? Indicate the negative (-) sign in your answer if the member is in compression. 12k 18 k 12 t D 36° 25 k 20 ft 16 ft
Question 1: Equilibrium of rigid body The uniform beam AD, which is supported by pin at point A and by roller at point C, carries the loads as shown in the figure below. Neglecting the weight of the beam and considering the system to be at equilibrium, (a) draw the free body diagram of the system (b) determine the reactive force at point C (c) determine the reactive forces at point A. 120 kN/m -2m- 100 KN B 2 m C + 120 kN/m o 2m 30⁰ D 120 kN