Electronic 2 For the opamp circuit shown below figure, calculate the followings by assuming A=∞o.1. What is the required value of C₁ to locate the pole frequency at 0,5 MHz?2. What is the required value of R2₂ to place the zero frequency of the system at the frequency of one-twentieth of the pole frequency?Circuit parameters / Devre ParametreleriR1=2,3 ΚΩ400C1 R1wVinR2wO a. C1=138,4 pF, R2=43,7kOb. C1=166,1 pF, R2=43,7k02O c. C1-193,8 pF, R2=36,8kQOd. C1-221,4 pF, R2=52,9kOe. C1=138,4 pF, R2=36,8kQOf. C1=249,1 pF, R2=29,9kg. C1=166,1 pF, R2=29,9kOh. C1=193,8 pF, R2=52,9kVoutE

Answered: Image /qna-images/answer/8d72f3e9-5043-4bf3-9c1f-5bd92921746a.jpg

For opan 1. What is the required value of C₁ to locate the pole frequency at 0,5 MHz? 2. What is the required value of R₂ to place the zero frequency of the system at the frequency of one- Circuit parameters / Devre Parametreleri Ry=2,3 ΚΩ 40 C1 R₁ HH un Vin R2 w Ao O a. C1=138,4 pF, R2=43,7k b. C1=166,1 pF, R2=43,7k Oc. C1=193,8 pF, R2=36,8k Od. C1=221,4 pF, R2=52,9k Oe. C1=138,4 pF, R2=36,8k02 Of. C1=249,1 pF, R2=29,9k Og. C1=166,1 pF, R2=29,9k Oh. C1-193,8 pF, R2=52,9k - Vout

For opan 1. What is the required value of C₁ to locate the pole frequency at 0,5 MHz? 2. What is the required value of R₂ to place the zero frequency of the system at the frequency of one- Circuit parameters / Devre Parametreleri Ry=2,3 ΚΩ 40 C1 R₁ HH un Vin R2 w Ao O a. C1=138,4 pF, R2=43,7k b. C1=166,1 pF, R2=43,7k Oc. C1=193,8 pF, R2=36,8k Od. C1=221,4 pF, R2=52,9k Oe. C1=138,4 pF, R2=36,8k02 Of. C1=249,1 pF, R2=29,9k Og. C1=166,1 pF, R2=29,9k Oh. C1-193,8 pF, R2=52,9k - Vout

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

d) Design (Find the values of the R₁, R2, and C₁) an astable multivibrator circuit to have an output waveform as shown below in the figure (tH = 375µs and t₁ = 125µs). (Assume C₁ = C₂ and R₁ # R₂) and determine the frequency of oscillation and the duty cycle. R1: R2 C1 Q Vcc 4 555 5 C2 10nF I 8 1 3L -OVO tH = 375.0us tL = 125.0us
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for continuous inductor current and an output ripple voltage of less than one percent. The load is a resistance of 50 2. Assume ideal components for this design. VL ooooo ip - ^
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
Q5/ Design a Colpitts oscillator as shown in figure below with 10 MHz output frequency. Find the values of C1, C2 and L1, then plot the waveforms at points P1 and P2. +Vcc R1 R4 P2 Cout Q1 Cin P1 R2 Re * Ce 升C1 * C2 Colpitts oscillator www.circuitstoday.com Your answer Q6/ Design a delay circuit using the IC 555, such that the delay between input and output to be 2 minutes. Draw the input/output waveforms. العربية الإنجليزية
Q2. For the circuit shown below, sketch i, & Vo 60 a. Find the conduction angle of the thyristor. b. Find the average output voltage V. R-6.50 f- Go Hz = 27AL = 120x17X10 = 6.4092 075 LO = RrjX= Vo L-17mH 6.5+j6.469=9.128 (44595 075 75V( Es 24 Vm A e
Signal subject 2
2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref +
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
In an ideal, steady-state and uninterrupted current mode, a Buck-Type DC-DC converter has a load resistance of 20 ohms, an output power of 120W, and a relative ripple in coil current b. What is the coil value in this circuit? (D-0.35,f-10 kHz) a) L-63.7 mH b) L-64 microH c) L=33.7 mH d) L=64H e) L-66mH
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V