For one of the diagonal members of your chosen bracing system propose a suitable section shape and size. Explain, with calculations where necessary, why you have chosen the proposed section. Then determine whether the strength of the section is adequate to resist an axial force of 90 kN. Assume the steel grade is S275 JR.

For one of the diagonal members of your chosen bracing system propose a suitable section shape and size. Explain, with calculations where necessary, why you have chosen the proposed section. Then determine whether the strength of the section is adequate to resist an axial force of 90 kN. Assume the steel grade is S275 JR.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.1P

See similar textbooks

Similar questions

In order to reinforce a column in an existing structure, two channels are continuously welded to the column as shown below. Fy = 50 ksi for both the column and the channels. The effective length with respect to each axis is 16 feet. a) calculate the Moment of Inertia about each axis of the built-up shape. a) what is the available axial compressive strength and what is the percentage increase in strength? Use both LRFD and ASD.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 24 kips, w = 2.2 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and Lcp = 15.8 ft. Determine the magnitude of the maximum bending stress in the beam. P B LAB LBC Answer: Omax tel i |C * ksi W LCD X
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 28 kips, w = 3.8 kips/ft, LAB = 4.6 ft, Lec = 4.6 ft, and Lco = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. %3D %3D B |C D LAB LBC LCD Answer: Omax = ksi
Stress Analysis of Trusses using method of sections. pls answer within 30 mins
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc = 5.2 ft, and LCD= 14.4 ft. Determine the magnitude of the maximum bending stress in the beam. %3D D B LAB LBC LCD Answer: ksi Omax
USE NSCP 2010 A simply supported beam is reinforced with 4 – 28 mm ø at the bottomand 2 – 28 mm ø at the top of the beam. Steel covering to centroid ofreinforcement is 70 mm at the top and bottom of the beam. The beamhas a total depth of 400 mm and a widthof 300 mm. fc’ = 30 MPa, fy = 415 MPa. Balanced steel ratio ρb = 0.031.Compute the ultimate moment capacity of the beam in kN-m. Usereduction factor of 0.90
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
write legibly Indicate all necessary FBDs, concepts and formulas needed in the solution. The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 27 kips, w = 2.8 kips/ft, LAB = 3.0 ft, Lec= 3.0 ft, and Lco = 16.4 ft. Determine the magnitude of the maximum bending stress in the beam. |C LCD LAB I LBC Answer: ksi Omax
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __ mm
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)