choose the correct answer oftheFoll owing1) CH and m() are used to geherate an ASignal the modulation index of the geheratedPseAM signal is 0.5 then the qualitysBisPc4 (P) () 49 710)2) A 4 GHZ carrier is D SB-SC modulaheda Low Pass message sighal withby amaximum freguency of 2MHZ the resulta ntsignal is to be ideally samPled. Theminimum freguency of the SamPLingimpuls is-a) 4 MHz ()8 )8GH2 (d18-004 GH2

Answered: Image /qna-images/answer/4c273c47-6cf1-4f6a-b720-660f6eb097c8.jpg

Foll owing- CH and m are used to geherate an A Signal the modulation index of the geh AM signal is 0.5 then the qualitySE is PsE Pc (a)士 ,(b)古 (c)号 (d) A 4 GHZ carrier is D SB-SC Modula with by a Low Pass message sighal aximum Freguency of 2MHZ the result signal is to be ideally sampPled. Th minimum Freguency of the SamPling impulsis:- k)8GH2 (d18004 8MHZ

Foll owing- CH and m are used to geherate an A Signal the modulation index of the geh AM signal is 0.5 then the qualitySE is PsE Pc (a)士 ,(b)古 (c)号 (d) A 4 GHZ carrier is D SB-SC Modula with by a Low Pass message sighal aximum Freguency of 2MHZ the result signal is to be ideally sampPled. Th minimum Freguency of the SamPling impulsis:- k)8GH2 (d18004 8MHZ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. For an AM, amplitude of modulating signal is 0.5 V and carrier amplitude is 1V.Find Modulation Index? modulating si gnal TE= 0S
Plz I need the correct answer of this question 1- The optimal value for the VSWR in RF circuits is: 1- infinity 2- 1 3-0 4- -1
To obtain SSB mark in single sideband modulation by applying filtering methodare required. The main band mark is band limited between 500 Hz and 1000 Hz, and the mark is at 100 MHzit will be transmitted. Obtaining the exit sign using the necessary stages in stages andexplain by drawing Spectra. Make the necessary calculations.
According to the figure below determine the following 1. What is the name of this type of modulation - 2. Determine the modulation index 3. Determine the amplitude of carrier and the amplitude of information signals 4. Write down the mathematical form of the signal assume the carrier frequency 10 MHz and information frequency 1 KHz. 5. If we want change the modulation index to be 1, how would your answer to parts three & four change? Amplitude 1.5 0.5 -0.5
* ?!s the following figure is the Deviation sensitivity of FM modulator No Yes A 100KHZ carrier with an amplitude of 2 V peak is modulated by a 1 kHz signal * ?with m = 0.2. What is the following answer is correct Vlsb= Vusb= 0.28 V O VIsb= Vusb= 0.1414 V O fusb= 101KHZ and flsb= 999KHZ fusb= 110KHZ and flsb= 99KHZ
Q4: An AM signal: XAM(1)-100cos(100z*10³ t) + 60cos(47*10') *cos(100 * 10³ t). 1) Calculate frequency bandwidth B for XAM(t) signal. 2) Modulation index m%. '
8.a. Which of the following statements about OSNR and BER is correct?A. BER isn't related to OSNR.B. Lower BER leads to a lower OSNR.C. Higher BER leads to a higher OSNR.D. Higher BER leads to a lower OSNR.8.b. An optical signal has a strength of 2.1 mW. What's this value in dBm?A. 2.11 dBmB. 2.32 dBmC. 3.10 dBmD. 3.22 dBm
Determine the modulation index for a frequency modulator with a deviation sensitivity of 10 kHz/V and a modulating signal of 5cos2π(4000)t
How it is generated Single Sideband Modulator Using Filter Method
3.) Determine the band width and baud for an FSK Signal with a mark frequency off99 kH2), aspace frequency of (2°1KHZ). and abit vate of lokbps).
1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is 5V. Calculate the bandwidth , modulation index ,Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHz
RF carrier 10 kV at 1 MHz is amplitude modulated and modulation index is 0.6. Peak voltage of the signal is? (a) 600 KV (b) 1200 KV (c) 6 KV (d) 10 KV