Find the tensien force in each 35 eable. A

Q: ment of each of the N (in N.m and co

A: given:F1=125NF2=150NF3=250N

Q: Find the Normal Force (in kilo-Newtons) in the rod of the system.

A:

Q: Find others Force applied =2.78N Area = 1mm?

A: Given data : Force=F Area=A   Required : Stress

Q: Determine the resultant mom ent 6+be fig. show n below:

A: Given data Forces acting are 800 N, 200 N

Q: If the wire diameter of a compressive helical spring is increased by 2%, the change in spring…

A:

Q: 45°, then find the work done. [A: 4]

A:

Q: Given data: Force=2 N Area =0.2 mm2 Determine stress

A: Given:-  Force = 2 N Area = 0.2 mm2 To Find:-  Stress

Q: уы =3 bafel beared Find the

A: Given data : Modulus of elasticity=E Bulk modulus=K   Required : Poisson ratio

Q: 1 of in 1of in s of r. ent A:

A:

Q: When the torque of car wheel is 27186Ncm and it has with the force of 0.91kN applied at the wheel.…

A: Given data, Torque of the car wheel, T = 27186 N-cm T = 271860 N-mm Applied force on the wheel, F =…

Q: Find the unit for H. Show all steps

A: Given, all the units of each parameter Substituting these values in the above equation,

Q: Find the Tension of cord AC in N Find the Tension of cord AD in N

A: Given data, Co-ordinates of A = (0,0,0) Co-ordinates of B = (2.5,0,0) Co-ordinates of C =(0,-2,0)…

Q: the curve OC is given by espect to the point O (0, 0)

A:

Q: intil its volume bec e work done by the elow, show the can ston and draw a fre

A: GIVEN:v1=14.5lv2=130.5lP=1720KN/m2

Q: ss of 1.5 tons and ction between the

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: hing 3304 kN is If the block is 9

A: Weight of block = 3304 kN Weight of sea water displaced = volume of water x density Volume of water…

Q: Given the internal radius of the pipe is 2 cm, the external radius is 2.4 cm and the length of the…

A:

Q: 2- the unit of line load is O kN2/mm pound kN/mm2

A: Line loads: Loads exert a load along a line, such as a partition's weight on the floor. Distributed…

Q: Find stress Force=2 N Area=2 mm2

A: Given data : Force=F Area=A   Required : Stress

Q: A 90 N force with an angle of 88° relative to positive x-axis clockwise. Then, a 75N force with an…

A: Given data: Draw the diagram of the system.

Q: Q3/ Determine the weight in Newtons a ine its weight in Pounds?

A:

Q: The red arrows represent the force of?

A: The red arrow represents the direction of motion of the Object.

Q: Find the welouty f flay A=2.1m2 = २० 0[S

A: Introduction : The question is related with fluid mechanics . In this question we are provided with…

Q: The value of b,

A: Given; The velocity field of an incompressible flow is given in question: Where, a1=2…

Q: and the

A:

Q: When the torque of car wheel is 27212Ncm and it has with the force of 0.31kN applied at the wheel.…

A: support diameter of car wheel is D. so, Torque on wheel is given by T = F× (D/2). here, F = 0.31 KN…

Q: Boil the kettle at your home. Determine the following e) Power of the kettle

A: In this demonstration students predict which kettle boils first. You can use it to illustrate that…

Q: Determine the rate of change of density?

A: V = volume of the tank = 0.73 m3. P = 485 kPa T = 40 oC = 313 K. R = 0.287 kJ/kg-K for air. A = Area…

Q: Find (Ix&ly), if a=30mm. a

A:

Q: 25°C respecti

A:

Q: ngth Land flexura Gon of the free en

A:

Q: Find the weight in Newtons of the steel ball if its diameter is 2 in. Use the density of steel as…

A:

Q: au that the gan AS = 3 Mcn taT

A: Entropy defines the randomness of the system. It measures the thermal energy of a system per unit…

Q: magnitude of the

A: Given; Stress free rod having length=200 mmAt room temperature is held between two immovalble…

Q: When the torque of car wheel is 273054Nmm and it  has with the force of 0.81kN applied at the wheel.…

A: Given : Torque (T) = 273054 N mm Force (F) = 0.81 kN   To find : Diameter of the car wheel (D) = ?

Q: Findss 30 kN-m

A:

Q: 2 Find T: For q=-KA when dr

A:

Q: Find the total magnitude of force, EFy acting in y-direction (answer in newton, N with a single…

A: In the given problem, following formulae for determining the resultant will be used Magnitude of the…

Q: Solve this

A: We have simply supported beam with reaction loads at A and E because of its support hinge at point A…

Q: on is given

A:

Q: haft trar Is, then t

A: given:power P=1000kwω=100rad/s

Q: determine P, in

A: COnversion chart 1 BTU 5.40395 psi ft^3 1 psi 6894.76 Pa     For a reversible process we…

Q: ine the value of P.

A:

Q: g has a diameter of de up of semicirc having reluctar

A:

Q: Calculate the work for the expansion in the process to 2 decimal places.

A: Thermodynamics : It is a branch of science which deals with work , heat , energy.  Also it studies…

Q: For the following Internal clovetails if b is yomm grater than C. M is 60 mm 25 mm less Find the…

A:

Q: If the wire diameter of a compressive helical spring is increased by 2% the change in spring…

A:

Q: two blocks each weighing 1.5 kN

A: Find the mass of each block.

Q: Find the stress Force=0.02 N Area 0.1 mm2

A: Given data : Force=F Cross sectional area=A   Required : Stress

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.