Find the resultant force (magnitude, direction and position) of a parallel force system. F1 = 40 lb up at 2 ft from point A; F2 = 70 lb down at 8 ft from point A; and F3 = 60 lb up at 13 ft from point A. Note: point A is the left end of the bar

Find the resultant force (magnitude, direction and position) of a parallel force system. F1 = 40 lb up at 2 ft from point A; F2 = 70 lb down at 8 ft from point A; and F3 = 60 lb up at 13 ft from point A. Note: point A is the left end of the bar

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Related questions

Q: In the clevis shown in Fig. 1-11b, find the minimum bolt diameter and the minimum thickness of each…

A: Given data as per questionLoad, P=63 kNAllowable Shearing stress, τ=38 MPaAllowable Bearing stress,…

Q: Multiple choice questions. Choose correct answer 1. Sampling is used because A) it increases the…

A: Sampling is a process used in the statical analysis in which a group of observations is. In this…

Q: Chip 1 has 3 Ring Oscilltors on it. Calculate the Calibrated Ring Oscillator value for Chip 1 and…

A: Given: To find: calculate the Calibrated RO_x

Q: An ideal gas mixture consists of 2 kmol of N2 and 6 kmol of CO2. The mass fraction of CO2 in the…

Q: For a slab with thickness 2 cm, the temperature is maintained at To and T₁ at x = 0 and x = L. When…

Q: Perform FMEA and Root Cause Analysis for any TWO problems faced in your industry.

A: introduction; FMEA is a failure mode and effect analysis. FMEA quality tools enhance the quality of…

Q: A reversible refrigeration cycle operates between cold and hot reservoirs at temperatures Te and TH,…

Q: Refrigerant 134a enters an insulated diffuser as a saturated vapor at 80°F with a velocity of 1400…

Q: Refer to the figure below and compute for the moment of force at point C -- (CW+) Mc FA = 600 N…

Q: P1(5, 20,10) will be rotated by 30 deg about the Z-axis. Followed by 90 deg about the X-axis, and…

Q: Water is the working fluid in a reheat-regenerative Rankine cycle with one closed feedwater heater…

A: We have initial pressure P1 = 1400 lbf/in2 intital temperature T1 = 1000 F h1 = 1493.5 Btu/lb S1 =…

Q: Q2: Given that the diameter of the bolt at C connecting the two members of the frame is 0.5 in,…

A: Given data:-diameter of the bolt (d)=0.5 in To find:-shear stress acting on the bolt

Q: 1. A steam power plant operates on a simple ideal Rankine cycle. The steam enters the turbine at…

Q: For the 2d coordinate system below, complete the following: a) Draw a dashed line that is parallel…

Q: force 15[kN-m¹²] 2m 25 [kN] 2m + A 2m X ir a Find location of the application of the posulfont…

A: Find the location of the application of the resultant force from point O

Q: 1. For hypothetical metal A in metal B, the diffusion coefficients are given at 2 temperatures: at…

Q: Task 3 Air at atmospheric pressure and a mean temperature of 327ºC flows through a steel pipe of…

Q: Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal…

A: given; lets take ;heat supplied in brayton cycle (Q1)=qHheat rejected in brayton cycle (Q2)=qL

Q: For a brick in the shape of a finite cylinder with a triangular cross section (as is used at the…

Q: 1. Show a detailed solution of each problem. Drawing of the schematic diagram of the cycle, and…

Q: For a glass/epoxy lamina with a 70% fiber volume fraction using the properties in the tables…

A: Solution: Given Data:

Q: TI Two cylinders are placed in a 18 ft wide container. The blue cylinder has a radius r₁ = 5 ft and…

Q: Ammonia in a piston-cylinder assembly undergoes two processes in series. Initially, the ammonia is…

Q: A bicycle tire pump has a piston with area 0.44 inches squared. If a person exerts a force of 30 lb…

A: Given Data- Area A=0.44in2 Force F=30lb We have to find Pressure produce

Q: Consider 4.8 pounds per minute of water vapor at 100 lb/in², 500°F, and a velocity of 100 ft/s…

A: Given DataP1=100 lb/in2=100 psiaT1=500°FP2=40 lb/in2m˙=4.8pounds

Q: Determine the location of the shear centre O of the thin-walled member of uniform thickness having…

Q: 400 mm A V = 75 KN 41- 200 mm 30 mm 30 mm

A: GivenV=75 kN

Q: Oil with the density of 950 kg/m³ and the kinematic viscosity of 2x105 m²/s is pumped from a tank to…

A: Given:Oil density, ρ=950 kg/m3Kinematic viscosity of oil, ν=2*10-5 m2/sPipe length, L=89 mPipe…

Q: Q.4 For the shown beam, draw the FBD, determine the reactions at the supports A and B and show them…

Q: fic heat, and thermal conductivity of the f 700 kg/m³, cp = 2400 J/kg K, and k = 0.34 ctively. The…

A: Given Data The thickness of the flaked cereal is:2L=1.2 mm The density of flake is:ρ=700 kg/m3 The…

Q: today the U.S. describes some of its arsenal as "smart weapons"-weapons that are intended to hit…

Q: A steam condenser is a heat exchanger which receives exhaust steam from an engine and cooling water…

A: Given data:- mass of steam =20,000 lb./hr, h1=1120 Btu/lb, h2 = 75 Btu/lb the temperature rise of…

Q: Consider a 2R planar manipulator with l1 = 1m, l2 = 1m. The final position is P1( X= 1.1m, Y=1.5m).…

Q: When the pole OA is in the position shown, the tension in cable AB is 7.8 kN. (a) Write the tension…

Q: Steam Turbine KJ Initially evacuated tank In case of emergencies, a turbine is connected to an…

Q: 1- What do we mean by alloy (Alloy), and why do researchers and specialists resort to its…

A: following is the answer to the above problem-

Q: 8in 96 16 35° pin in slot 6 in 12 in A A 5 in 8 in For the frame and loading shown, find (a) the…

Q: A long thin walled cylindrical shell, closed at both the ends, is subjected to an internal pressure.…

A: To find : ratio of hoop stress to longitudinal stress in the cylindrical shell

Q: Ammonia in a piston-cylinder assembly undergoes two processes in series. Initially, the ammonia is…

Q: A car traveling along the straight portions of the road has the velocities indicated in the figure…

Q: A dual cycle has air operating as the working fluid. The air begins the compression process at 100…

Q: 50 LY

A: Given

Q: ANSWER COMPLETELY FOR UPVOTE a. When do we say that the body is accelerating? b. What's the…

A: (a). When velocity of a body increases with respect to time, we say that the body is accelerating.…

Q: A cylinder and piston assembly contains water at 105°C and 85% quality, with a volume of 1 liter.…

A: Given Datak=100N/mmT1=105°Cx1=85%V1=1L=0.001m3V2=1.5L=0.0015 m3d=150mmT3=600°Cx3=25%

Q: Four forces are applied to the machine component ABDE as shown. Replace these forces with an…

A: Given: To find : equivalent force-couple system at A

Q: Water is the working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater.…

Q: A hot air balloon is tethered to the ground with three cables as shown in the figure. If the balloon…

Q: A three-process cycle operating with 5.0 kg of air as the working substance has the following…

Q: Steam at 120°C flows in a cast iron pipe (k = 80 W/m K) whose inner and outer diameters are Di = 5…

Q: I need answer ASAP. Thank you!

A: To find z coordinate

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the forces in the three cable segments and the angles 1,2, and 3.
Q3b. Force vectors F1 and F2 act on body P with the resultant force vector R. The resultant force R= 350 N and the angle between R and the x-axis is of 35°. If F1 = 180 N and the angle between F1 and the x-axis is 72º, determine the angle between F2 and the x-axis. Assume coplanar vector forces and give your answer in degrees to two decimal places. F1 R F2 Body, P Answer:
HOME WORK 3 Determine the resultant force at A. for the figure below Hint : 1- Find the position of all points A,B,C (x, y, z) 2- Find FAR and FAC 3- Find |raR| and Iracl 4- Find FAR = F UAB and FAC = F UAC 5- Finally find R and a, B,Y 3m Fc= 500N FB= 500N 3m 5m 3m B 4m 2m 5m
Find the resultant for this system of forces: F2= 81 lb F1 = 100 lb 4 ft B 3 ft 7 ft 40° 4 ft
The following concurrent forces are acting on a body in xy plane: A 300 lb pointing up to the right 30 degrees with x axis, 400 lb at 45 degrees with x axis acting up to the left, 200 lb down to the left at 60 degrees with x axis, 150 lb down to the right at 75 degrees with x axis and a 100 lb directly to the right. Determine the resultant force and its direction using graphical and analytical method. Pls show the solution, formula and free body diagram.
Find the forces at points A and B. C = 300 lb ft R = 150 lb 4 ft. A 3 ft. B
Considering the figure below, the volume loaded at point A is a force of F pounds in wire AB.constitute. This force creates the force F from point A to point B in Cartesian vector form.Express.(F=309daN)
R is the resultant coplanar-concurrent forces composing of P, T, F, and each Q acting on a body. Find the magnitude of the fourth force Q and its angle with respect to horizontal, if P = 840N directed downward to the left at 20 degrees with the vertical, T = 890N is acting to the right along the horizontal, F = 530N is up to the right at 45 degrees with the horizontal and R = 1300N acting downward to the right 30 degrees with the horizontal. Show your answers in graphucal and analytical method
The following concurrent forces are acting on a body in xy plane: A 300 lb pointing up to the right 30 degrees with x axis, 400 lb at 45 degrees with x axis acting up to the left, 200 lb down to the left at 60 degrees with x axis, 150 lb down to the right at 75 degrees with x axis and a 100 lb directly to the right. Determine the resultant force and its direction using graphical and analytical method. Show solution, formula and the FBD and pls write legible
2. The force P = 2 kips is applied to point A, and is supported by cable AB, cable AC, and bar OA. The force P and both cables pull on point A, and bar OA pushes on point A. Determine the forces in cables AB and AC, and in bar OA. You can use Excel to solve the equations, but you don't have to for this one. (Point A lies in the zy plane, and points B and C lie in the xz plane.) 6 ft x 4 ft B 4 ft 12 ft AC D 5 ft P 12 ft
Q4: The forces F1 and F2 act on a bracket as shown in the Figure below. Determine the magnitude of the resultant force. F = 100 N C 20° F2 = 90 N
= 35 N, F2 = 10N, F3 =5 N, F4 =35N, F; = 40N , F6 = 10N & F7 =80N. The angles e, =15°, e; =40° , e, = 40°, es = 40 ° Find the magnitude and direction of the resultant force for the system of forces shown in the figure. Where F1 F2 F3 F1 F4 F7 Fs F6