Find the power required to drive a 40-mm power screw having double square threads with a pitch of 6 mm. The nut is to move at a velocity of 60 mm/s and move a load of F = 16 kN. The frictional coefficients are 0.08 for the threads and 0.12 for the collar. The frictional diameter of the collar is 60 mm.

Find the power required to drive a 40-mm power screw having double square threads with a pitch of 6 mm. The nut is to move at a velocity of 60 mm/s and move a load of F = 16 kN. The frictional coefficients are 0.08 for the threads and 0.12 for the collar. The frictional diameter of the collar is 60 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 3 A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of 34 mm and a pitch of 6 mm is used. The coefficient of friction at the thread and collar are 0.15 and 0.1 respectively. If the collar frictional diameter is 100 mm and the screw turns at a speed of 1 rev/s. (Given dm = 31mm, 1 = 6mm, dc = 100mm). Find: (a) the power input to the screw. (b) the combined efficiency of the screw and collar.
A double square thread power screw has a pitch of 6 mm and mean radius of 34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required to turn the screw.
Find the power required to drive a 1.5-in power screw having double square threads with a pitch of 1/4 in. The nut is to move at a velocity of 2 in/s and move a load of F = 2.2 kips. The frictional coefficients are 0.10 for the threads and 0.15 for the collar. The frictional diameter of the collar is 2.25 in.
(5) A 2½-in square thread steel screw is used in a common jack screw. There are 2¼TPI. The body of the jack is made of cast iron. The coefficient of friction on the threads is 0.15. The thrust collar at the top has an inside diameter of 1½-in & the outside diameter of 3.0in. The coefficient for the collar is 0.25. The load to be lifted by the jack screw is 2 tons. Determine: (a) the efficiency of the screw only; (b) the efficiency of the screw & the thrust collar; (c) the pull necessary @ the end of a 2.0ft lever to operate this screw jack.
A double-threaded power screw is used to raise a load of 5 kN. The nominal diameter is 60 mm and the pitch is 9 mm. The threads are Acme type (2θ= 29°) and the coefficient of friction at the screw threads is 0.15. Neglecting collar friction, calculate:(i) the torque required to raise the load; (ii) the torque required to lower the load; and (iii) the efficiency of the screw for lifting load
(11) Find the power required to drive a power screw lifting a load of 40001b. A 2½-in double square thread with 2TPI. is to be used. The frictional radius of the collar is 2-in and the coefficients of friction are 0.1 for the threads and 0.15 for the collar. The velocity of the nut is 10fpm.
3 The press shown below has a rated load of 25 kN The twin screws have Acme threads, a diameter of 56 mm, and a pitch of 5.5 mm. Coefficients of friction are 0.05 for the threads and 0.08 for the collar bearings. Collar diameters are 88 mm. The gears have an efficiency of 95 percent and a speed ratio of 60: 1. The full-load motor speed is 1750 rev/min. a. When the motor is turned on, how fast will the press head move? b. What should be the horsepower rating of the motor? Bearings Motor Spur gears Bronze bushings (مزدوج) Foot Worm Collar bearing
(9) A single thread trapezoidal metric thread has a pitch of 4mm &has a mean diameter of 18mm. It is used as a translation screw in conjunction with the collar having an outside diameter of 37mm & inside diameter of 27mm. Find the required torque in N-m to raise a load of 400kg, if the coefficient of friction is 0.3 for both threads & the collar.
What force will be required at a radius of 80 mm to raise and lower an 11 kN crossbar of a planer that is raised and lowered by two 38 mm single-start square thread screw having a pitch of 7 mm? The outer and inner diameters of the collar are 76 and 38 mm respectively. Assume the coefficient of friction at the threads as 0.11 and at the collar as 0.13.
4 A double-threaded power screw with square threads pushes against a load of 3,641 N at a speed of 15 mm/s. The screw has a major diameter of 20 mm and a pitch of 3 mm. The frictional coefficient of the threads is 0.25, and collar friction is negligible. What is the rotational speed of the screw in units of revolutions per minute? Type your answer 2 points
Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The angle of V is 55° and the load is carried on a swivel head of mean diameter 60 mm. the coefficient of friction between the nut and screw is 0.16 and that between the swivel head and the spindle is 0.1. Calculate the load required to be applied at the end of two levers each of effective length of 500 mm to raise an axial load of 1 KN and the efficiency of the lifting.
A single square-thread screw has an input power of 3 kW at a speed of 1 rev/s. The screw has a diameter of 40 mm and a pitch of 8 mm. The frictional coefficients are 0.16 for the threads and 0.09 for the collar, with a collar friction diameter of 50 mm. Find the axial resisting load Fand the combined efficiency of the screw and collar if the screw is raising the load. The axial resisting load Fis |kN. The combined efficiency of the screw and collar is %.