Find the load that can be lifted by applying a force of 200 N at the end of 450 mm long lever of screw jack using single start square thread. The pitch of the thread is 12 mm and mean diameter 65 mm. The load does not rotate with the screw spindle. The C.O.F. between threads is 0.15 and for collar is 0.12 with mean radius 40 mm. Find also the efficiency.

Find the load that can be lifted by applying a force of 200 N at the end of 450 mm long lever of screw jack using single start square thread. The pitch of the thread is 12 mm and mean diameter 65 mm. The load does not rotate with the screw spindle. The C.O.F. between threads is 0.15 and for collar is 0.12 with mean radius 40 mm. Find also the efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single threaded trapezoidal metric thread has a pitch of 4 mmand a mean diameter of 18 mm. It is used as a translation screwin conjunction with a collar having an outside diameter of 37mmand an inside diameter of 27 mm. The load is 400 kg and coefficientof friction is 0.3 for both threads and collar. Find:a. The collar torqueb. The required torque for threadc. The total torque
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
CB Page view A Read aloud Add text V Draw Highlight A 550 rpm shaft fitted with a 35 inches diameter pulley weighing 300 lbs. This pulley delivers 40 Hp to a load. The shaft is also fitted with a 26 inches pitch diameter gear weighing 220 lb. This gear delivers 30 Hp to a load. Assume that the tension of the tight side of the belt is twice that on the slack side of the belt, determine the concentrated loads produced on the shaft by the gear in Ibs. Select one: a. 753.85 b. 462.61 C. 484.44*** d. 264.44
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?c. What maximum torque is necessary to lower the load?d. What is the maximum torsional shear stress induced on the screw?
34 in 3. The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
I need correct answer At stationary the tension in pulley 120N. Find tension in each side and Power trans when belt is on the point of slipping on smaller wheel. The wheel is 250mm diameter and fac F Friction 0.32. The angle of Lap 165⁰. The wheel speed 1200 C/min.
has a double- The gear puller shown in Fig. threaded square-threaded screw with a mean radius of in., a pitch of 0.1 in., and a coefficient of friction of 0.30. The gear is wedged onto its shaft and requires a force of 100 Ib to remove it. Determine the moment that must be applied to the gear puller screw to remove the gear.
Problem: A double-threaded power screw with ISO metric trapezoidal threads is used to raise a load of 300 kN, The nominal diamter is 100 mm & the pitch is 12mm. The coefficient of friction at screw threads is 0.15. Neglect the collor friction. Q.45 Torque required to raise the load is
In a bolted joint two members are connected with an axial tightening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque required for achieving the tightening force is
A single square thread power screw has a lead of 7 mm and mean diameter of 35 mm. If it Is used to lift a load of 30 kN and coefficient of friction of thread is 0.18, find the torque required to turn the screw.
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.