A spring is stretched 30cm by a mass of 2kg, and the mass is attached to a viscousdamper that exerts a force of 6N when the velocity of the mass is 2m/s.a.) Find the differential equation that characterizes u(t), the displacement of the massfrom equilibrium t, when it is set in motion. Specify the units that you are using and showfind the parameters in the equation. You do not need to solve the equation here.howyoub.) Find a fundamental pair of solutions for the equation you found in part a.c.) The mass is pulled down 40cm from the equilibrium and then thrust downwards withan initial speed of 2m/s. Find u(t).

Answered: Image /qna-images/answer/a7885367-951e-459b-a83f-a15a3c04b303.jpg

Answered: Find the differential equation that…

Engineering

Mechanical Engineering

Find the differential equation that characterizes u(t),

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 An object of mass 125 kg is released from rest from a boat into the water and allowed to sink. While gravity is pulling the object down, a buoyancy force of times the weight of the object is pushing the object up (weight = mg). If we assume that water 40 resistance exerts a force on the object that is proportional to the velocity of the object, with proportionality constant 10 N-sec/m, find the equation of motion of the object. After how many seconds will the velocity of the object be 90 m/sec? Assume that the acceleration due to gravity is 9.81 m/ sec2. Find the equation of motion of the object. X(t) = %3D
Look at the below system. Using either the conservation of energy method or Lagrange's method, solve for the governing equation of motion for the system. Put a box around your final answer. Also, put a box around your equations for the potential and kinetic energy of the system. Assume the system's springs are initially unstretched (i.e., assume that there is no gravity until t = 0 [s]). K₁ Î E K₂ X
A mass weighing 24 pounds, attached to the end of a spring, stretches it 4 inches. Initially, the mass is released from rest from a point 2 inches above the equilibrium position. Give the initial conditions. (Use g 32 ft/s? for the acceleration due to gravity.) x(0) X ft %3D x'(0) ft/s Find the equation of motion. x(t) X ft Need Help? Read It Watch It
The ideal gas law, discovered experimentally, is an equation of state that relates the observable state variables of the gas--pressure, temperature, and density (or quantity per volume): PV = NkBT (or pV = nRT), Figure L₂ Lx 1 of 1 Part A Find the magnitude of the average force (F) in the x direction that the particle exerts on the right-hand wall of the container as it bounces back and forth. Assume that collisions between the wall and particle are elastic and that the position of the container is fixed. Be careful of the sign of your answer. Express the magnitude of the average force in terms of m, vr, and L₂. ► View Available Hint(s) Submit Part B IVE ΑΣΦ ? Imagine that the container from the problem introduction is now filled with N identical gas particles of mass m. The particles each have different x velocities. but their average x velocity squared. denoted
4. Consider a mass of 500 g placed at the end of a spring with stiffness constant 100 N/m and hanging at rest. The mass is displaced downward by 1.0 cm and released from rest. When the motion sets in, a time-varying force F(t) = cos³ 2t is applied to the spring-mass system. Solve the nonhomogeneous 2nd order differential equation representing the motion. That is, solve for x(t). [Note: Take the downward direction as the negative x-axis.]
Q4/ Write the displacment equation y(t) of the system below if (m=3.5 kg K=2.5 N/mm and C= 0.018 N.s/mm) : 2 m k
Find the differential equation of the mechanical system in Figure 1(a) To obtain the differential equation of motion of the mass and spring system given in Fig. 1. (a) one may utilize the Newton's law for mass and spring relations defined as shown in Fig. 1. (b) and (c) use f = cv for viscous friction, where v is the velocity of the motion and c is a constant. Z/////// k M F. F, F F F, F, k EF=ma F = k(x, - x,) = kx (b) (c) Figure 1: Mass-spring system (a), Force relations of mass (b) and spring (c)
Hitting a Golf Ball A golf ball is hit so that its height h in feet after t seconds is h(1) = =16r² + 64t. (a) What is the initial height of the golf ball? (b) How high is the golf ball after 1.5 seconds? (c) Find the maximum height of the golf ball. (d) What is the domain and range of h in the con- text of this application?
Q1:- Find the time period of the fluid in a U-tube manometer shown by using Newton Method. Fluid densilj e Tube arca A. KA Q2:- Find the natural frequency for the system shown in the figure using the energy method. 2m R R 4R 3m Q3:-Find the natural frequency for the system shown (assume massless links) by using Energy Method. ki k2 a a w
4-IF =x*yz, then div grad p is equal to. d: zero a2yz f+6x yz j SZyz'i + x*zj+3x*yz ) b: 2yz + 6xyz 5- When the force is a fimction of distance we can obtain the concept of e: Kinetic and potentraf energy d: Torque Terminal velocity b: Impulse
2. A kilogram mass is attached to the end of the spring with spring constant 2 N/m. Find the equation of motion if the mass is initially released (set in motion) from rest from a point 1 meter above equilibrium position. (Use the convention that displacements measured below the equilibrium position are positive.) (a) Write the initial-value problem which describes the position of the mass. (b) Find the solution to your initial-value problem from part (a). (c) Graph the solution found in (b) on (0
A forensic scientist test-fires a projectile (mass mP) at a cubic block (volume V), made from wood (density D), resting on a rough surface (static = kinetic coefficient uS). The bullet enters the block with an initial velocity vo and exits the block with a velocity v1. The friction forces on the bullet as it passes through the length of the block are unknown and are assumed to be constant. Solve these problems algebraically first: a) What is the deceleration of the bullet inside the block? How many "g" is that? b) How much time does it take the projectile to pass through the block? c) What is the velocity of the block as the bullet exits? d) How long (time) and how far (distance) does the block slide after the bullet has exited? e) Solve the above numerically for the following parameters (g =9.81m/s^2): mP = 10g, V = 0.1m^3, D = 500kg/m^3, µS = 0.8, v0 = 500m/s, v1 = 100m/s