Figure Q5 shows the cross-section of the typical layout of two tracks (A and B) on a printed circuit board with a ground plane C. The tracks are terminated as shown in the figure, with track A carrying digital signals. You can assume that the lines are electrically short. Draw the equivalent circuit that models the crosstalk and write down a relation between the voltage applied to track A and the voltage coupled on to track B at low frequencies, VNE-. (a) (b) If the total mutual inductance between the two tracks L =9 nH, and the total mutual capacitance between the two tracks is C = 2 pF, calculate: (i) the amplitude of the near-end pulse VNE- (ii) the amplitude of the near-end pulse VNE if the driven line is terminated in a short circuit instead. Comment on the crosstalk. A B C 50 Ω 50 2 A V(t) 50 2 VNE VE 3 50 N V{t) 5 V 50 ns 50 ns 1 us

Figure Q5 shows the cross-section of the typical layout of two tracks (A and B) on a printed circuit board with a ground plane C. The tracks are terminated as shown in the figure, with track A carrying digital signals. You can assume that the lines are electrically short. Draw the equivalent circuit that models the crosstalk and write down a relation between the voltage applied to track A and the voltage coupled on to track B at low frequencies, VNE-. (a) (b) If the total mutual inductance between the two tracks L =9 nH, and the total mutual capacitance between the two tracks is C = 2 pF, calculate: (i) the amplitude of the near-end pulse VNE- (ii) the amplitude of the near-end pulse VNE if the driven line is terminated in a short circuit instead. Comment on the crosstalk. A B C 50 Ω 50 2 A V(t) 50 2 VNE VE 3 50 N V{t) 5 V 50 ns 50 ns 1 us

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

A final year project student, Raphael, learns in EEE307 that an oscillator circuit with a differential output can be built using single-ended tuned amplifiers like the one shown below: VDD C₁=R4₁ - Vout VinM₁ Fig. 3.1 Single-ended tuned amplifier schematic (image adapted from B. Razavi ©2012)
Briefly describe the trade-offs between ripple adders and adders with carry look-ahead.
An ac LVDT has the following data; input 6.3V, output 5.2V, range ±0.50 cm. Determine: a) Plot of output voltage versus core position for a core movement going from +0.45cm to -0.03cm? b) The output voltage when the core is -0.35cm from the center? c) The core movement from center when the output voltage is -3V? d) The plot of core position versus output voltages varying from +4V to -2.5V.
about nyquist stability criterion in deatials
What is load curve
Q2:- By using IC 74151 Construct the following Function: F(A,B,C)= Eodd no.-1
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system
Write an 8051 ASM program to load the timer 1 in order to generate 2000 Hz square wave as given in Figure. The square wave should be generated on pin 2 of port 3. Assume the crystal frequency is 16 MHz. ON 4* Delay Delay
Good day! Please help me determine the conduction angle in my simulation as well as the delay angle. Please teach me also how to determine it. Thank you! need asap.
The value of critical clearing angle can be directly determined by using step by step method.Select one:True fals
How do we know current flows in source terminal? Is this common for n-type mosfet? What is an n-type mosfet?
Explain the stages seen in the given power supply block structure, respectively, and draw the output signals at the points indicated by A, B, C and D in scale.