Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal to the output angle (82 - 04) and the transmission angle is 30°. The input link is extended beyond joint B and an input force (Fi) is applied at the end of it, while an output force is drawn from the midpoint of the output link. If an output force of 30 N is desired from an input force of 10 N, how far the input link should be extended, Le, what is the distance from point B to the point where Fin is applied. Fa Fost A. D Non-scaled diagram; AB = 10 , CD =r4 = 30 (output), all in mm %3D

Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal to the output angle (82 - 04) and the transmission angle is 30°. The input link is extended beyond joint B and an input force (Fi) is applied at the end of it, while an output force is drawn from the midpoint of the output link. If an output force of 30 N is desired from an input force of 10 N, how far the input link should be extended, Le, what is the distance from point B to the point where Fin is applied. Fa Fost A. D Non-scaled diagram; AB = 10 , CD =r4 = 30 (output), all in mm %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Find a combination of link lengths where motion of a point on output link is one quarter of a circle. 2. Find the value of all 0, 0, 0, and y in open and close configuration Read the value of link lengths and the input angle 8., then use the formulae given below to calculate the value of unknowns 03, 0, and y K₁ = = K₂= d K2 K3 = a²-b²+c²+d² 2ac A = cos 0₂ - K₁ - K₂ cos 0₂ + K3 B = -2 sin 0₂ C = K₁ (K₂ + 1) cos 02 + K3 -B± √B²-4AC 2A 0412 = 2tan-1 d K₁ = — K5 = c²d²a²-6² 2ab D = cos 0₂ - K₁ - K4 cos 0₂ + K5 E = -2 sin 0₂ FK₁+ (K₁ - 1) cos 02 +K5 0312 2 tan-1 (-E± -E± √E²4DF 2D Y = 04-03
The link lengths and the value of 2 and offset for some fourbar crank-slide linkages are defined in Table 1. The linkage configuration and terminology are shown in Figure 1. For the rows assigned, find (a) all possible solutions for angle and slider position d by vector loop method. (b) the transmission angle corresponding to angle 83. (Hint: Treat the vector R4 as virtual rocker) Show your work in details: vector loop, vector equations, solution procedure. Table 1 Row a b с offset 02 Link 2 1.4 3 5 A R2 0₂ Link 3 4 8 20 slider axis. R3 Link 3 R₂ d R₁ Figure 1. 0₁ Offset 1 2 -5 С B R4 T 84 X Q2 45° -30° 225°
The figure below shows an offset slider crank linkage. The links lengths are: link2 = a= 100 mm and link3 = b = 600 mm. The offset is c = 190 mm. we need to : 1. determine the maximum horizontal position of the slider B (dmax) and the corresponding input angle 02 2. determine the minimum horizontal position of the slider B (dmin) and the corresponding input angle 02 Y 03 y В R3 R4 R, 04 R2 02 d ► X R1 The maximum horizontal position of the slider is dmax = Choose... + The input angle 02 corresponding to dmax , in degree and measured CCW from X axis, is = Choose... + The minimum horizontal position of the slider is dmin = Choose... + The input angle 02 corresponding to dmin , in degree and measured CcW from X axis, is = Choose.. +
Q1: For a four-bar linkage. If a=5.5m, b=6m, c=8m and d=D10m. 1: Find the minimum of the transmission angle in degrees 2: Find the maximum of the transmission angle in degrees 3: Find 0, at the toggle positions in degrees bola
Problem 4-6a The link lengths (a, b, c, d) and the value of 2 for a crank-rocker linkage are defined as 2, 7, 9, 6, 30°, respectively. Draw the scaled linkage. Find all possible solutions (both open and crossed) for angles 03 and 04 graphically. Орen B A LNCS 4 a GCS र 4 4" Crossed (This is not the scaled kinematic diagram.) Problem 4-7a Repeat Problem 4-6a except solve by the vector loop method.
Problem 3: The RPH robot of Figure 3 is shown in its zero position. Determine the end- effector zero position configuration M, and the screw axes S; in {s}. n. F -inta. Sorowo- Zs {s} Xs L₁ ŷs Lo 0₁5 L2 02 {b} zb 103 pitch h = 0.1 m/rad Ấb ŷb L3 Figure 3: An RPH open chain shown at its zero position. All arrows along/about the joint axes are drawn in the positive direction (i.e., in the direction of increasing joint value). The pitch of the screw joint is 0.1 m/rad, i.e., it advances linearly by 0.1 m for every radian rotated. The link lengths are Lo = 4, L₁= 3, L2= 2, and L3= 1 (figure not drawn to scale).
Problem 4-15h Find the input angles (02) corresponding to the toggle positions of a non-Grashof double- rocker linkage with link lengths (a, b, c, d) of 10, 10, 10, 20, respectively.
1. Determine binary, ternary link and quaternary link for the given kinematic chain as shown in figure below and also find the number of degrees of freedom by using Kutzbach criteria. 2.Explain with neat line diagram how Scotch yoke mechanism is used in control valve actuators in high-pressure oil and gas pipelines, as well as in various internal combustion engines, such as the Bourke engine.
Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage mechanism, calculate instantaneous torque, required to drive the mechanism and to present the results of the case study in a clear reporting format. Introduction: Figure 1 shows a pumpjack operating at an oil well. Its representation as a linkage is also shown in Figure 1. The pumpjack is driven by a motor attached to crank OA. A constant torque T is applied to the crank and the crank rotates at a constant angular velocity ???. A force P is applied vertically downwards at the end of the walking beam BD, which has its centre of mass at point G. To design the mechanism, a careful kinematic analysis of the mechanism needs to be conducted. To avoid mechanical failure and to provide adequate support to the mechanism, the engineer needs to analyse the reaction forces in the joints. Masses of links OA and AB are assumed to be smaller in comparison with the mass of BD and are ignored in the analysis.…
2) Block 4 slides in a slot in the fixed piece 1. Axis Q₂ of crank 2 is fixed on 1. Q₂₂A = 1 1/2 in., and AB = 4/1/2 Draw the mechanism, assuming limen- sions for 1, if desired, or use center lines only. Draw the four-bar linkage for this mechanism, properly rotate the linkage Q₂ ABQ400; Name each link, and show the finite and infinite cranks. Frind graphically the two extreme positions of 13, The axis of the pin by which link 3 is attached to the block 4.. Dimension the length of the stroke of B. Ans. 3& in. for scale 1:1
1-draw velocity vectors showing the motion of points Band C.2-Label The IC of Velcoity, If it does not exsist mention why 3- What type of motion is each link experiencing at this instant? Rotation about afixed axis, Pure Translation, or General Planar motion? and why (justify your answer )
4. A general fourbar linkage configuration and its notation are shown in the following figure and table. Find a 3, a 4,A¼, ABA, AB,Ap for open circuit by vector loop method. Row Link 1 Link 2 Link 3 Link 4 02 Rpa 63 6 2 7 9 30 10 6 30 - 12 - 15 7 3 8 85 25 3 10 6 8 45 -10 10 80 d 7 25 24 - 4 45 e 75 -50 10 300 Rp B A 03 2 X 04 NO O55