Figure 4.1 below shows a series RLC circuit. Q4.1 Given the input and output voltages, determine the transfer function of the circuit. Q4.2 Qualitatively show that this circuit can be considered as a band reject filter. Vi Vi + (+ L Vo Figure 4.1 Circuit diagram for Questions Q4.1 and Q4.2. The same series RLC circuit is again used but this time the voltage across the resistor is taken as the output. See Figure 4.2 below. L C HE Q4.3 Determine the transfer function of the circuit. R{ C HE R + Vo WITH Figure 4.2 Circuit diagram for Questions Q4.3 and Q4.4.

Figure 4.1 below shows a series RLC circuit. Q4.1 Given the input and output voltages, determine the transfer function of the circuit. Q4.2 Qualitatively show that this circuit can be considered as a band reject filter. Vi Vi + (+ L Vo Figure 4.1 Circuit diagram for Questions Q4.1 and Q4.2. The same series RLC circuit is again used but this time the voltage across the resistor is taken as the output. See Figure 4.2 below. L C HE Q4.3 Determine the transfer function of the circuit. R{ C HE R + Vo WITH Figure 4.2 Circuit diagram for Questions Q4.3 and Q4.4.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4: A Low pass filter (current mode conversion) is shown below: R: io Using a current source I, an R and L, to sketch a high pass filter and describe briefly how it works?
4 Are the filters shown in Figure P6.24 low-pass, high-pass, bandpass, or bandstop (notch) filters? V,(ja) REVC0) (a) ll V(ja) REKCja) (b) -ww R1 V,(j0) 12 c+ R2V C) all
For the signal flow graph of the ints given figure consider the following statements: 1. It has three forward paths. 2. It has three individual loops. 3.lt has two non touching loops. out of above the correct statements are X2 X3 О 2,3 O 1,2 O 1, 2, 3 О 1,3
A) Write the equation for the small-signal gain function Vout/Vinfor the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system
What is the definition of resonant frequencies, cut-off frequencies, bandwidth, andquality factor of series and parallel RLC circuits.And how do you determine the circuit conditions at the resonant and cut-off frequencies. (Answer in long paragraph form)
Determine the overall transfer function for the system as shown in Figure Q4.
Design a 3 Band Equalizer based on the following requirements. Use standard component values on your circuit design. The design specification values have a tolerance of +/- 3% of the rated value for cut/boost while a tolerance of+/- 10% of the rated value for frequency values
(c) LVDT will be used to measure work piece motion from -1.2 cm to 1.4 cm , the static transfer function (sensitivity) =23.8 mV/mm find: 1) The voltage output range. 2) The position when V,= -300 mV. 3) If the resolution changed to 0.5 mm what will be the resolution of the output voltage.
Figure P4.8 shows the asymptotic Bode plot of a bandpass filter. Design a circuit that realizes the given frequency response. Give the transfer function and find the gain K.
Design an ACTIVE band-pass filter for the midrange part of a loudspeaker so that the bandpass region is 400 Hz-2000 Hz (as defined by the -3dB points). Design the circuit so that the absolute gain is 2. a. Draw the circuit diagram and specify the resistor and capacitor values. Assume you can use either 100, 330, 500, or 1000 Ohm resistors and can select any value of capacitor. b. Sketch the frequency response (Gain [dB] vs. frequency (Hz)). Note that you will need to convert your gain to dB before plotting. Magnitude (dB) 15 10 5 midrange 12 1 -5 -10 -15 -20 -25 10 100 1,000 Frequency (Hz) 10,000 100,000
6. An AC precision integrator is desired for a particular application to perform the operation: Vo'(t) = -1200 Vi(t) dt The primes indicate the ac portions of the respective functions. The lowest frequency other than a possible de component of the input signal is estimated to be 1.5 kHz. Determine a suitable design. 7. A low frequency differentiator is desired for a particular application n to perform the operation Vo(t) = -0.002 dvi(t)/ dt Based on a periodic signal with a frequency of 1 kHz, determine a suitable design. 8. Design an astable 555 timer circuit to produce 1kHz square wave, where TH = 0.35 ms and T₁ = 0.65 ms. Select C = 0.01 UE, Determine R₁ and Ra. 9. Design a monostable 555 timer circuit to produce an output pulse 5 ms wide. 10. Using op amps with Xsat = +/- 13 V, design a square/ triangular wave function generator circuit to generate 2 kHz triangular wave with a peak-to-peak voltage of 12 V. 11. Design a non inverting Schmitt trigger circuit with VT to be adjustable…
Q4. (a) Write brief notes (taking a maximum of 10 minutes, i.e. minute") on RC filter circuits, including in your discussion: • RC circuit layouts for low pass (LPF) and high pass (HPF) filters. Labelled plots of their frequency responses (i.e. bode plots). • One common LPF application and one common HPF application.