External support reactions: RA = L1 Consider the following values in the given beam above: L1 = 6 m L2= 2 m L3 = 4 m L4 = 2m L5 = 2m L6 = 1 m W1 = 90 kN/m W2 = 20 kN/m P = 40 KN M = 50 kN-m RC = RF = KN KN W1 KN L2 The maximum positive moment at segment AC is The maximum positive moment at segment CF is The maximum shear along the entire span of the beam is The maximum positive moment along the entire span of the beam is The maximum positive moment along the entire span of the beam is L3 2 m E kN-m. kN-m. It is located at W2 kN. L4 kN-m. kN-m. L5 M G L6 H m from point A. Express all your answers in three decimal places. For the reactions, there is NO NEED to put the sign. For Y and M values ALWAYS include the sign (+ or -) to denote the nature of sheer and hending Not indicating the sign will mark

External support reactions: RA = L1 Consider the following values in the given beam above: L1 = 6 m L2= 2 m L3 = 4 m L4 = 2m L5 = 2m L6 = 1 m W1 = 90 kN/m W2 = 20 kN/m P = 40 KN M = 50 kN-m RC = RF = KN KN W1 KN L2 The maximum positive moment at segment AC is The maximum positive moment at segment CF is The maximum shear along the entire span of the beam is The maximum positive moment along the entire span of the beam is The maximum positive moment along the entire span of the beam is L3 2 m E kN-m. kN-m. It is located at W2 kN. L4 kN-m. kN-m. L5 M G L6 H m from point A. Express all your answers in three decimal places. For the reactions, there is NO NEED to put the sign. For Y and M values ALWAYS include the sign (+ or -) to denote the nature of sheer and hending Not indicating the sign will mark

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Numericai 1- For the following bar element, find the reactions at supports using FEM if EA=10000 t 12 t 6 m. -3 m 2- For the following bar element, find the reactions at supports using FEM if E=2000 t/cm? 2 t 0.5A 0.25A K1m* 2 m *1m+ 3- Resolve problem 2, if the free end is supported by fixed support. 4- For the following bar element, draw N.F.D. using FEM if E=2000 t/em A= 8 cm? A=4 cm TUm 1t/m' 4m 4m
Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 т B 50° A
Determine the components of reaction at the ball-and-socket joint A and the tension in the supporting cables DB and DC. Z. 1.5 m В 1.5 m C m 1.5 m 800 N/m 3 m -1.5 m +1 m 3 m Answers: Ax = %3D Ay = Az = FDC = FDB
Q4: Determine the reactions at the supports A and B shown in the Figure Below due to the applied forces for the following cases: A) Neglect the weight of the beam. B) Consider the weight of the beam which is 50 N and located at the center of the beam (3.5 m from A) 600 N 200 N 0.2 m 45% -2 m 3m 2 m 100 N Page4
Determine the reactions for the following loaded beam , 2ym 5 N JO Nm A B TON Im 2m Im 1-5m
Two rods of diameter d = 3 in are joined together: a C83400 brass rod, and a %3D 2014-T6 aluminum rod. The length of the brass rod is L1 = 2 ft, and the length of the aluminum rod is L2 = 3 ft. A force of magnitude F = 422 Ibf is %3D %3D %3D exerted on the assembly at a distance of L ft from A. Determine the magnitude of the reaction force at A. Express your answer in Ibf. B. F L2
Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
A beam is supported as shown below: Hinge A E B D F 1 m 1 m 1 m 1 m 1 m The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: LOAD W(DL) W(LL) P(LL) SET 1 (1,2,3,4,5) 20 25 40 Determine the following: 1. Maximum reaction at A, RA in kN. (
18. If a close coiled helical spring absorbs 30 Nmm [S-toof energy while extending by 5mm, its stiffness will be (b) 4 N/mm (a) 2 N/mm sqa-bun ann and (c) 6 N/mm (d) red boxit 10 N/mm q
For the truss given below, what is the retraint that can not be remove to arrive with primary structure? CHOICES: a. Member AD b. Member BC c. Reaction at B d. Horizontal Component of the reaction at A thank you!!
For the truss given below, what is the retraint that can not be remove to arrive with primary structure? CHOICES: a. None b. Reaction at D c. Reaction at C d. Vertical Component of the reaction at A thank you!!!
The ratio of reactions Ra and Rgof the simply supported beam, as shown in figure below, will be 5t 3t 2t/m A. B E R, R, - 2 m 2 m 2 m 2 m