Explain in detail various types of automation layouts with neat sketch
Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2
A: Given data: ◆ The stress developed in the area: σ = 2 N/mm2 ◆ The cross-sectional area: A = 2 mm2…
Q: A constant boundary generated by the collective effects of the MMC limit of size of a feature of…
A: Given data: A condition boundary generated by the collective effects of the MMC limit of size of a…
Q: Q4: For the frame shown in Fig.(4), determine the components of reaction at pin C
A: Given
Q: Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A…
A:
Q: A/ Saturated steam is flow in a double pipe heat exchanger at 250°C. The length of the heat…
A: Given Data Temperature of steam Ts=250°C Length of heat exchanger L=10m inner dia; of pipe…
Q: A person holds horizontally a 20 Kg bar with both hands (see Figure 2.1). The hands are 1.5 m apart…
A:
Q: Actual air fuel ratio= HU 22.97 (32 +3.7 x 28) 1.875 (8x12 +18) 14.57
A: The optimal air to fuel ratio for a gasoline engine is known as the stoichiometric mixture, which…
Q: The combined mass of the crate and platform AB is 400 kg with the mass center at C. Members DA and…
A: Given: Mass of the combined crate and platform AB is, m=400kg Member DA: Angular velocity,…
Q: Two plates each having an area of 5 m^2 are 127 mm apart. The plate on top is fixed while the plate…
A:
Q: 2. Let A be the scouring pad, B be the sponge, and C be the 100-g soap box. Arrange A, B, and C on a…
A: Friction force manifests itself when there is relative motion between the surfaces or a tendency…
Q: 1) "Fuel is spent to make the vehicle go uphill, as you are aware. However, the fuel will not be…
A: As we know thermodynamics is a branch of engineering that deals in heat, heat output like work, heat…
Q: A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio…
A: Given: Speed of crankshaft, ω1=523.6rad/s Third gear ratio, 1.62:1 The final chain reduction is,…
Q: can you answer part a and please accept the mass on the right (2m) as 2.5kg , the one on the left…
A:
Q: Determine the reactions at A for the cantilever beam subjected to the distributed and concentrated…
A: Given Data: Uniformly varying load's (UVL) magnitude is 2.8 kNm UVL is distributed over 2.5 m length…
Q: A material condition used to indicate that a specified geometric tolerance applies at each increment…
A:
Q: A diesel power plant supplies energy for a certain Cooperative. During a 24-hr period, the plant…
A: Given data: during 24 hr period the plant consums 200 dallons pof fuel at 301k and produced…
Q: Consider the flow of a Newtonian fluid through a circular tube which is placed horizontally.…
A:
Q: The pendulum is suspended from point O and consists of two bars, each weighing 10 lb. Determine the…
A: Weight of each bar = 10 lb Length of OA= 2 ft Length of BC = 2 ft It is required to determine the…
Q: Two L 152x102x12.7 angle brackets are welded to a steel plate that is 16 cm tall and has a width d…
A:
Q: The Sylvania Super Saver 75 W light uses 20 watts, produces 1280 lumens, and costs $4.49. As an…
A: Given Data The power consumption of the super saver light bulb is:PssL=20 W The light intensity of…
Q: Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in…
A: Given DataE1=74 GPaA=1749 mm2L=738 mmE2=204 GPa
Q: A circular container has a diameter of 3.5 m. How many hours can this storage supply an engine…
A: Given: The diameter of circular container, d = 3.5 m The fuel API = 25 degree The fuel consumption,…
Q: Kerosene is placed inside a glass capillary tube having a radius of 0.5 mm. The kerosene inside the…
A: Given: Tube radius = R = 0.5 mm Standing height of kerosene level = 59 mm Surface tension of mercury…
Q: EXAMPLE . During service, a ceramic valve which is operating at 250°C is likely to be suddenly…
A: Write the given properties for both ceramics A and B. A B Young's modulus E(GN/m^2) 120 350…
Q: A rectangular plate is supported by brackets at A and B and by a wire CD. If the tension in the wire…
A: Given data: T=200 N Need to determine the moment about A of the force exerted by the wire on point…
Q: The collar has a mass of 2 kg and is attached to the light spring, which has a stiffness of 30 N∕m…
A: Given data: m=2 kgk=30 N/mL0=1.5 mF=50 N Need to determine the velocity v of the collar as it passes…
Q: A cord is wrapped around each of the two 13-kg disks. They are released from rest. Suppose that r 74…
A:
Q: A vehicle engine is producing a brake power of 56 kW with a torque of 132.2 Nm. The final drive…
A:
Q: 1.44 The slider travels along the guide rod AB with the velocity v = 6 m/s. of (a) the unit vector…
A:
Q: Gear A of the winch turns gear B, raising the hook H. Gear A starts from rest at t=0 and its…
A:
Q: Just after launch from the earth, the space-shuttle orbiter is in the 35 x 152-mi orbit shown. At…
A: Given data: VA=17242 mi/hr Need to determine the speed of the earth at perigee.
Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…
A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…
Q: What is the vertical reaction component at A for the frame shown? 3 k/ft 45.0 k Select the correct…
A: Given: Length of CD=20 ft Length of DE=5 ft And uniformly distributed load on bar CDE is 3k/ft Now…
Q: The primary datum feature controls the Size Flatness of the part?
A: Datum is a reference point, line or surface with respect to which measurements or study of part is…
Q: Consider the series springs shown in accompanying figure. Realizing that the total deflection of the…
A: When a combination of springs attached end to end i.e., in series combination then, Force in each…
Q: Question 3 For the mechanism shown in Figure 3, the gear has constant clockwise angular velocity of…
A:
Q: a) A rigid tank containing refrigerant 134a is initial at -18 °C with the quality of 30%. Due to…
A: Given: The initial temperature of R134a, T1 = -18 C The quality of refrigerant, x = 0.3 The rate of…
Q: QUESTION FIVE: (a) State the purpose of conducting a Morse test on an internal combustion,…
A: a) Purpose of conducting Morse Test on an Internal Combustion, reciprocating piston engine are as…
Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…
A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…
Q: Calculate the work produced by the 25-N force at an angle 30 degrees from the horizontal which…
A:
Q: A circular pipe 2 m long carries water and tapers uniformly from diameter 0.1 m at point A to 0.2 m…
A:
Q: Specify the Ø1.00-inch pin perpendicular to the top surface of the plate in Fig. 6-19 within a…
A: Given question: Specify the Ø1.00-inch pin perpendicular to the top surface of the plate in Fig.…
Q: A tape weighting 2 lb (A=0.006 sq.in.); E=29,000,000 psi) has a length of 100.00 ft under a pull of…
A: Calculate the sage correction. Cs=124WP2L=12423522686=0.3654
Q: Find Ax and Ay F2= 450 N 45° 14- y F₁ = 300 N Ay 5 3 Ax F3 = 600 N -X
A:
Q: 5.) Using Gaussian Elimination, solve 1 1 3 0 1 2 1 1 0203 -1 0 2 1 W y Z 3 3 0
A: Given, The matrix is, 11112-1300203-1021wxyz=3310
Q: Kerosene is placed inside a glass capillary tube having a radius of 0.5 mm. The kerosene inside the…
A:
Q: A baseball is thrown downward from a 50-ft tower with an initial speed of 18 ft/s. Determine the…
A:
Q: The link AB of a mechanism is 40 cm long. It is undergoing plane motion in X-Y plane and the…
A: Given data The length of the link AB is:rAB=40 cm=0.40 m The acceleration of A is:aA=12 m/s2 The…
Q: A car is capable of reaching 27 km/h from rest in 4 seconds on a level road against resistances…
A: Given data: vi=0vf=27 km/h=7.5 m/st=4 secm=1200 kgM=700 kgVi=0Vf=36 km/h=10 m/s Need to determine…
Q: A block 4, of mass m is connected through a cable and a pulley to an elastic spring (see figure…
A: Given data: k=100 N/mθ=45°m=85 kg Need to determine the distance covered by the block when it stops…
Explain in detail various types of automation layouts with neat sketch.
Step by step
Solved in 3 steps with 1 images
- Explain the basic terms , application and advantages of CNC programming ?Question No.13: a.) Explain CAD system architecture with neat sketch. b.) Discuss the applications of CAD and CAM in the manufacturing environmentIn robot programming, what is the difference between powered leadthrough and manual leadthrough?
- The fundamentals of CNC programming, as well as G and M codes, are explained in depth.a. With the aid of diagrams describe how a production plan is generated for a traditional 'push' planning and control system and compare this to a 'pull' system b. In terms of machine utilisation, discuss the benefits and drawbacks of each? 7 c. The following options have been proposed to reduce the inventory level for the situation outlined in Q4c. Option A: The delay time T is halved (T/2) Option B: Capacity C is increased to 200 units Option C: X becomes 12.5%With reference to robot geometry, what kind of robotic configuration would be best suited for material removal in automobile industry, Justify your answer. Mention industrial applications for other configurations also This subject is robotics and automation of ece pls solve neatly and faster thanks
- Guide Questions: 1. In your own words, how will you describe a microcontroller? 2. What is the role of a microcontroller in robot programming? 3. In your opinion, can robots think on their own? Explain further.Can someone please help me to solve this graphically on CAD as well as analytically. Show all work thank you!(a) Describe THREE (3) distinguishing features between NC and CNC systems. (b) Define the following, as applied to NC systems: (i) Control Resolution (ii) Accuracy (iii) Repeatability (c) Explain why CNC systems are suited for batch production. (d) Despite its numerous advantages, describe TWO (2) downsides (other than the cost) of having CNC systems. (e) With regard to motion control in CNC sytems, describe the differences between 'point to point' and 'continuous path' systems. (f) Explain what is meant by 'Computer-Integrated Manufacturing'. (g) Describe the importance of CAD/CAM packages in modern manufacturing plants, especially in a Flexible Manufacturing System. Show transcribed image text