[Exercise 1] Measure the height difference between points A and B with a level instrument. It is known that the elevation of point A H, is 12.658m, the center cross reading of A ruler is 1526mm (a= 1526mm), and the center cross reading of B ruler is 1182mm (b). What is the height difference hAB between the A and B points? What is the elevation of point B H₂?

[Exercise 1] Measure the height difference between points A and B with a level instrument. It is known that the elevation of point A H, is 12.658m, the center cross reading of A ruler is 1526mm (a= 1526mm), and the center cross reading of B ruler is 1182mm (b). What is the height difference hAB between the A and B points? What is the elevation of point B H₂?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Describe about the Dilatometer Method.
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG EXPLANATION. ANSWER IN 2 DECIMAL PLACES.) 9.82 Compute the ¯Ix and ¯Iy for the annular region.(Ans: Ix = 4.084 × 106 mm4, ¯Iy = 0.816 × 106 mm4)
According to the figure below, fill out the table showing all your calculations: a) find the elevation of TP2 b) perform the arithmetic check BS 1.27 BM Elevation 356.68 *All values are in feet. STA BM ΤΡΙ TP2 B.S. 1.27 FS 4.91 H.I. TP₁ BS 2.33 F.S. FS 6.17 Elevation TP₂
The screed readings were successively monitored using a leveling device and the device was moved after the sixth and second reading. If you know that the level of the last point is 36.51 meters. And that the readings between the brackets are an inverted straightening the ruler upside down (find other proportions in another way). 2 3 4 5 10 1 8 9. (1.652) 1.623 1.123 1.833 1.492 1.570 1.350 1.928 0.987 (2.115)
In Compass traversing length of lines are measured by O a. Dumpy level O b. Theodolite O c. Chain O d. Compass 2.
Give me both right answer with explanation. Which of the following would produce the greatest error when taping a distance of 100' with a steel tape? a. the tape is supported throughout but pulled with too litte tension b the tape is 2' off line c the tape is supported throughtout but pulled with too much tension d. the tape is on a 5% slope without correcting for it After a day of field work, you should copy and/or rewrite you field notes to make them nearer and more readable. True False
Add 1 cm and 1 m A. 50 cm B. 101 cm C. 250 m D. 150 m
Given: F |Change in length of BE=0.00352a mm Area(BE)=150a mm? Area(CF)=150a mm? E=200 GPa Required: |Change in length of CF? 18a mm 2ба mm P - 24a - mm
I am not sure that I am doing this right up to the point that I scanned...is it supposed to be W_B=-5pi rad/sec or...? Thank you for the help!
The stress of a structure is shown in the figure below. Assuming that the El of the entire beam section is constant, try to analyze the stress state of the structure, and try to draw the Shear Curve and Moment Curve of the beam.
The following readings were taken with a level and 4 m staff. Draw up a level book page and reduce the levels by the height of instrument method and Rise and Fall Instrument. STA B.S I.S. F.S. Н. R.L. BM1 0.74 101.75 1 0.89 1.765 3 2.17 CP1 0.375 2.95 1 1.888 2 1.181 СРЗ 0.474 2.07 1 1.177 2 1.217 СР4 0.617 3.125 1 0.67 2 0.704 BM2 1.74 Σ
QUESTION 6 1. The following data were taken from PEG method of adjustment. Point 1 is midway between A and B. Point 2 is 20m to the left of A and 120m from B. Determine the difference in elevation between A and B. (give your answer in two decimal places) Instrument at 1 3.0 2.0 Rod Reading on A Rod Reading on B Instrument at 2 2.75 1.50