Example: Neglect the base currents. (a) What logic function is performed by this circuit? (b) What are the logic 1 and logic 0 values of Vo at the output? (c) When VA = logic 0 for one of the two inputs, determine i, iic ic and Vo (d) Repeat part (c) when all inputs are logic 1. VA 2.6ΚΩΣ Va iz 5V 1.2ΚΩ Q₁ Q₂ 1.6V Vo 0.8k02

Example: Neglect the base currents. (a) What logic function is performed by this circuit? (b) What are the logic 1 and logic 0 values of Vo at the output? (c) When VA = logic 0 for one of the two inputs, determine i, iic ic and Vo (d) Repeat part (c) when all inputs are logic 1. VA 2.6ΚΩΣ Va iz 5V 1.2ΚΩ Q₁ Q₂ 1.6V Vo 0.8k02

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
) The input waveforms in are applied to logic circuit in figure below. Determine the output waveforms. B G2 C C D D E
(b) Figure Q2(b) shows input waveforms of A, B and C. Draw the logic circuit that will generate the output waveform X. A Inputs B Output X Figure Q2(b) : Input and output waveforms
Derive the state table and the state graph for the following logic circuit: A' B' B DA Clock Clock X B'
Q2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
Draw logic diagram for half adder and full adder circuit using Logisim Software
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
Design a counter that counts 1-2-3-5-7 Please explain the following:state diagram state table simplification Logic circuit digital design
Find: a. written simplified boolean expression b. written truth table c. all output that results in 1
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef