Ex.3.2 (Eng'g Mech by Meriam) For the given jib crane shown, draw the FBD of the beam AB. The beam AB is a standard 0.5m l-beam witha mass of 95 kg per meter of length. The forces ON the beam AB are the: (1) tension exerted by the cable at B, 0.25 m 25° B 0.5 m (2) the applied pull (3) the reaction of the pin 1.5 m - 0.12 m at A and 10 kN (4) its own weight 5 m

Ex.3.2 (Eng'g Mech by Meriam) For the given jib crane shown, draw the FBD of the beam AB. The beam AB is a standard 0.5m l-beam witha mass of 95 kg per meter of length. The forces ON the beam AB are the: (1) tension exerted by the cable at B, 0.25 m 25° B 0.5 m (2) the applied pull (3) the reaction of the pin 1.5 m - 0.12 m at A and 10 kN (4) its own weight 5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.1 Formative Assessments Problem 1 4.5 The homogeneous beam AB weighs 400lb. For each support conc shown in (a) through (d), draw the FBD of the beam and determine the numt unknowns. Cable 12 ft B A 6 ft 6 ft B A C 40° (а) (b) Cables 60° 30° 12 ft B A 12 ft В (c) (d) Fig. P4.5
Q2 :The railway wheel exerts a force on the rail and through the wooden beam, and the gravel can be assumed as a reaction over the length of the wooden beam, as shown in Fig. Q2. (a) Draw the shear force and bending moment diagrams for the beam and determine the magnitude of the maximum load w per kN/m. (b) If the allowable bending stress is 10 MN/m² and the aspect ratio of the rectangular wood beam is h/b = 0.5, determine the minimum width b and height h that can be used for the beam. 60 kN Į 45 cm 60 KN Uniform Reaction w kN/m 150 cm 45 cm Fig. Q2 Railway Loading
(a) A beam of length 6 m is subjected to the loading as shown in Fig. 3a. The UDL acts between A and C and has the value of 4 kN/m. Point loads of 6 kN and 10 kN act at points B and E respectively. Draw fully labelled shear force and bending moment diagrams showing all the important values (i.e. weight of the beam assumed negligible). 6 kN 10 kN 4 kN/m A, B. 2 m 2 m 1m 1m Fig. 3a
2. A ladder 12 m long leans against a vertical frictionless wall with its lower end 3 m from the wall. The ladder weighs 40 N. Find the magnitude and direction of the force exerted on the lower end of the ladder. 3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert?
3.14 A horizontal beam is 4m long, its built-in at the left hand end A and simply supported at the right hand end B. the beam carries uniformly distributed vertical loading of 18KN/m over its whole length together with a vertical downward load of 10KN at 2.5m from the point A. sketch the B.M and S.F diagrams with indicating all values. 3.15 Plot the shear force and bending moment diagrams of the beam loaded as shown in the figure qa²/2 55
A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at the center of the beam, what is the tension in the right rope?
Q5: For simply supported beam AB shown in Fig.(5), find the value of L so that absolute maximum moment due to moving loads will not exceed 300kN.m 12m B 40KN 40KN 30KN Fig.(5) L 2L
1. Three forces and an applied moment act on the beam with a fixed-end support. (a) Determine x and y components of each force (based on coordinate system drawn). (b) Draw FBD. (c) What motion does the fixed-end support restrict? (d) Solve for ALL the reactions at the support. m 1 m 0.3 m 0.5 4 kN m 1.5 m 70° 15 kN-m 10 kN 6 kN 0.3 m
A 4 m 300 N/m D C 2 m 2 m B 0000 300 N (a) Determine the support reactions at A and B. (b) Reduce the problem to a system of forces, distributed forces and couples acting on beam AB (c) Draw the shear and bending-moment diagrams for beam AB, (d) Determine the magnitude and location of the maximum absolute value of the bending moment.
Q.2) A person uses an exercise band with an elastic modulus (spring constant) of 35 lb/ft. They begin the exercise with their arm relaxed in the vertical position (OA), at which point the band is unstretched. The person rotates their arm up to the horizontal position shown, so that their shoulder is at point O and their hand is at point B. Determine the moment exerted by the elastic band on the person's shoulder joint in this position. 24 in B. 24" (F 28 in C
P.1) The rigid rod of length L is free to rotate in a horizontal plane. A moment Mk is applied to the vertical shaft that connects to the rod at O. What are the reaction forces acting at O in terms of é, the rod's angular speed, M, m, the mass of the rod, and L? M i L-
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. For the beam shown, Q-150 kips. 2 ft 2ft 2ft 2 ft 2 ft B Determine the magnitude Pof the two upward forces for which the maximum absolute value of the bending moment in the beam is as small as possible. (You must provide an answer before moving to the next part.) The magnitude Pis kips