Electric machines / I need a complete expert solution in handwriting for the question. Please provide a correct solution. A 4 pole, 240 V, wave connected shunt motor has 540 conductors. and gives 11.19 kw when running at 1000r.p.m and drawing armature and field current of 50 A and 1A respectively. Its armature resistance 0.1 2. assuming a drop of 1V per brush find (a) Total torque, (b) Useful torque, (c) useful flux / pole, (d) efficiency

Electric machines / I need a complete expert solution in handwriting for the question. Please provide a correct solution. A 4 pole, 240 V, wave connected shunt motor has 540 conductors. and gives 11.19 kw when running at 1000r.p.m and drawing armature and field current of 50 A and 1A respectively. Its armature resistance 0.1 2. assuming a drop of 1V per brush find (a) Total torque, (b) Useful torque, (c) useful flux / pole, (d) efficiency

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
A 10 kW, 250 V shunt motor has an armature resistance of 0.5 Ω and a field resistance of 200 Ω. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full load and rated voltage, the line current is 40 A and because of armature reaction, the flux is 4 % less than its no-load value. What is the full load speed?
1. The useful full load torque of a 3-phase 4 pole, 50 Hz induction motor is 162.84 lb-ft.The rotor e.m.f is observed to make 60 cycles per minute. Calculate (a) Motor output (b) Copper loss in rotor (c) Motor input (d) Efficiency if mechanical toque lost in windage and friction is 22.46 lb-ft and stator losses are 850 W
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .
4-pole DC in series motor, 180 Nm torque. The coil is wavy, at 600 total conductors, and the magnetic flux per electrode is 0.02 Weber. The resistance of the product and log windings is 0.2 ohm and 0.1 ohm, respectively. Calculate the copper knob if the reciprocating force generated is 205 volts
A 220 V DC series motor runs drawing a current of 30 A from the supply. Armature and field circuit resistances are 0.4 and 0.1 respectively. The load torque varies as the square of the speed. The flux in the motor may be taken as being proportional to the armature current. To reduce the speed of the motor by 50% the resistance in ohms that should be added in series with the armature is
A 10 kW, 250 V Shunt motor has an armature resistance of 0.5 ohm and a field resistance of 200 ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full load and rated voltage, the line current Is 47 A and because of armature reaction, the flux is 4 % less than it no load value. a.) What is the full load speed? b.) What is the developed torque at fll load?1158 rpm
A 230V d.c.shunt motor takes 5A at no load and runs at 1000 r.p.m. Calculate the speed when loaded and taking a current of 30A.The armature and field resistances are 0.2N and 230 N respectively.
Q/ dc shunt motor 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * Cu loss is……watt * Mechanical , electrical and overall efficiency …… Output of the prime motor…….kwatt * The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * Flux per pole is......... wb * E.M.F. generated is………….volt *
A 4 pole, (01*10)V, DC shunt motor operates on a load current (1*10)A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. b) what will be the factors to minimize the back emf?
A 500 V, lap wound d.c. A shunt motor has 90 slots and each has 8 conductors. When the motor delivers full load it draws a current of 30/ A from the line. The field and armature resistances are 250 ohm and 0.4 ohm respectively. If the fixed resistance is 27.1 mWh, find the speed of the motor and the torque produced.