EE-310 Signals and Systems - Homework 4 d. Can this system be realized? Explain. e. Find the system output for an input æ(t) = cos(t). f. Find the system output for an input æ(t) = e³nt. g. Find the system output for an input æ(t) = cos(2t + 0.57)+ ejnt. h. Find the system output for an input whose X(N) = 8(2) + H

EE-310 Signals and Systems - Homework 4 d. Can this system be realized? Explain. e. Find the system output for an input æ(t) = cos(t). f. Find the system output for an input æ(t) = e³nt. g. Find the system output for an input æ(t) = cos(2t + 0.57)+ ejnt. h. Find the system output for an input whose X(N) = 8(2) + H

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ASAP It is a type of diode where it operates as a variable resistor when heated. Your answer What is the modulation index in ideal condition of AM. Your answer A form of AM where a sideband is filtered after its carrier is eliminated. Your answer What is the form of AM that used to transmit video signals of the TV system? Your answer It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency. It is the extent to which the amplitude of the carrier wave is varied by modulating wave.
Fill in your bole algebra training with karnaugh in the image.(Do not discount.)
O d. FM demodulator Choose the correct statement(s) that describe the diagram below. - x,(1) Bandpass filter Envelope detector Limiter Differentiator Select one or more: a. FM Demodulator b. Narrowband to wideband conversion OC. PM Demodulator Od. Linear PLL model e. FM Discriminator with bandpass limiter A third-order PLL can track a frequency-ramp with zero steady-state nhase error
Signal and system problem.plz solve every step with formula
DIGITAL COMMUNICATIONS H.W. Q1/ A) Find the sampling frequency for the following signals: 1) S1 = 20 cos(1500nt) * cos (4000nt) 2) S2 = sin (200xt. 3) S3 = sin4000nt + 5 cos(1200nt) nt B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 02/ The following data stream (10011011 11001110 11110000 10001000 11100000 11011010 11111111 01110111 10011001 11100111 01011010) will be transmitted with signaling rate equal to 80 k bit/sec. 1- Find the data transmitted using L- parity, V- parity and L&V parity. 2- Find the Hamming code of the last byte of the data only in which two error can be detected and one error can be corrected, calculate the transmitted bandwidth? how can reduce the transmitted bandwidth? Explain and calculate the reduced…
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
Determine the transfer function from Uin to Uut! b) Set up amplitude and phase function! c) Assume that we connect 10V (DC) as input voltage at time t-0. How much voltage is then above C2 after a long time?
Q2/ Write True or False for the following: 1) The discrete-time system is a device or algorithm that performs some prescribed operation on the discrete-time signal. 2) When there is overlap occur when Ws-Wm < Wm so the spectrum of the continuous signal cannot be reconstructed. 3) A non-periodic function that occurs twice in time and repeats itself again. 4) (D/A) converters "connect the dots" in an analog signal
Q2- Explain by equations and block diagram the direct method demodulation in NBFM Q3- Write the formula of the phase modulation (PM) when Ac=25 , Fc=10® Hz, Kp= 20 . If an information signal m(t) = cos(212000t) + 10sin(2n2000t) Q4- Drive a formula for NBFM by using Bessel function Q5- If an information signal X(t) = cos(2n700t) + 10cos(25000t). Write the formula of the frequency modulation (FM) when Ac=20 , Fc=10® Hz, Kf= n2000 Q6-) If NBFM signal passes through a frequency multiplier. With B < 0.5 and fc=200kHz. Let fm ranges from 50OHZ to 15kHz, and let the maximum frequency deviation Afat the output be 75kHz. Find the required frequency multiplication n and the maximum allowed frequency deviation at the input. Q7- If an angle modulated signal S(t) = 10[cos(210®t) + 15sin(2n10³t)]
For the given circuit below, the RF generator is set to EXT MOD, 500kHz. RF GEN 500KHZ R1 2702 R2 10K ELECTRONIC VOM 0.0047pF a) What is this circuit? b) Is there an RF signal across R2? c) Draw the expected signal waveform across R1 d) Draw the expected signal waveform across R2 e) What is the expected frequency of the signal across R2?
2) A voltage signal consists of the following periodical waveform: V(t) = 10 sin 502.7t + 5 sin 94.2t + 15 sin 942.5t where t is in seconds and Vin volts. This signal is sampled digitally at a sampling frequency of 200 Hz. 128 data points are taken. a) Recommend additional procedures to sample the signal properly in the frequency domain considering the sampling conditions given above. b) Sketch what the frequency spectrum would look like if you were to perform an FFT on these sampled data. Label your axes carefully. c) Calculate: - the total sampling time - the time increment between sampled data points - the frequency resolution of the frequency spectrum - the Nyquist frequency
BW mssege signai COTier. i) Draw the modulated signal in ii) find the bandwidth of the modulated signal ii) What is phase reversal and we could avoid it? frequency domain, (AM)