EASE HELP ME CHOOSE WHAT CORRECT LETTER OR ANSWER 1. The direction of induced voltage in a conductor can be changed by a. increasing the field strength. d. decreasing conductor size. b. reversing the field direction. e. reversing meter connections. c. increasing conductor length. 2. Direct current can be supplied to a load by a loop of wire rotating through a field with the use of a. slip rings. b. c. brushes. electromagnets. d. commutator. e. conductor. 3. Induced voltage can be increased in magnitude by a. increasing the number of lines cut per second. b. using a commutator. c. using slip rings. d. decreasing conductor length. e. properly applying the left-hand generator rule.

EASE HELP ME CHOOSE WHAT CORRECT LETTER OR ANSWER 1. The direction of induced voltage in a conductor can be changed by a. increasing the field strength. d. decreasing conductor size. b. reversing the field direction. e. reversing meter connections. c. increasing conductor length. 2. Direct current can be supplied to a load by a loop of wire rotating through a field with the use of a. slip rings. b. c. brushes. electromagnets. d. commutator. e. conductor. 3. Induced voltage can be increased in magnitude by a. increasing the number of lines cut per second. b. using a commutator. c. using slip rings. d. decreasing conductor length. e. properly applying the left-hand generator rule.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

13.a. Eddy-current loss in the stator core can be reduced by usingA. alloys with low resistivity.B. annealed iron laminations.C. silicon alloys of copper.D. thin laminations of steel.13.b. Which one of the following is damaging to many insulating materials used in alternators?A. Eddy currentsB. SaturationC. CoronaD. Hysteresis
Explain very briefly about the flux fringing and their place of occurrences.
fill inthe blank : field winding has large numberofturns of thin copper wire. a. Shunt b. Series c. Compound d. separately excited
3. a) List the difference between destructive and non- destructive testing b) Give five examples of materials used for the design of any type of insulation. c)when a transformer full of magnetic material is overloaded and heats up what do you think would happen to the magnetic properties, and which law would the material be associated with in you understanding?
14/. The purpose of brushes in a dc machine is__________. to change ac to dc signal to remove the losses in machine to collect voltage from windings avoid spark for current
A. The brushes used in a DC generator a) ride against the commutator segments. b) are made from material softer than the commutator segments. c) are generally marked Al and A2 d) all of the above B. A magneto is a DC generator that uses for its pole pieces. a) electromagnets b) permanent magnets c) either "a" or "b" d) neither "a" nor "b"
These are different types of alumunium conductors. Which one is good and why? Kindly compare...
the armature mmf can be -2 reduced by reluctance of the magnetic the circuit in the region of the pole .tip a) Increasing, O b) decreasing O c) don't put O
The task is to draw or illustrate the armature winding, using the description below: -4 poles -26 conductors -double layer -simplex wave winding
List three applications of electrical transformers.
13.The armature of 6.6 kV, 3-phase, 20-pole, 300 rpm, Y-connected armature has 180 slots. The flux per pole is 0.08 Wb and the coil span is 160ᵒ Determine the number of conductors in series per phase
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.