e two wattmeter method: (Sen appendix B. WI Z. L30 L20 W2 W1 Vacla cos(30° – Oa) - W2 Vbela cos(30° + Ob) %3D I am trying to work out power using the two watt method. I have all the angles needed Vac and Vcb but I do not have Vbc, how can I work out W2 using Vcb? Would the cos(Angle) change? Vab=230

e two wattmeter method: (Sen appendix B. WI Z. L30 L20 W2 W1 Vacla cos(30° – Oa) - W2 Vbela cos(30° + Ob) %3D I am trying to work out power using the two watt method. I have all the angles needed Vac and Vcb but I do not have Vbc, how can I work out W2 using Vcb? Would the cos(Angle) change? Vab=230

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
%23 IoA 1172 IAB wwww IBC 20L-90°y -J992 204 30°y A ICA IcC a) Find the load current ICA ? b) Give the line yoltoge Vab? C Calculate the total complex power over the saurces of the voltoge7 www
What will be the value of the twiddle factor: W42
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
8. For this circuit, find the current I₁. A) 5.87+j0.88 A B) 6.35 +j1.41 A C) -48 +j24 A D) 2.27+j0.54 A 1852 -j452. 12060V 4:1 1252 jlsz
Hard: Basic: Write the currents on the following ammeters. HHH+ 1. The resist of equal the rema 0.45A 0 30A 0.15A 6. SAY 3. The p hob. show con Medium: sup ide 8. 0.30A (A A0.6A 0.30A 11. 0.3A 0.15A 0.45A 12. 13. 0.05A Villiers High Sehool
If a load is leading, which statement is NOT true? a. The load is capacitive. b. It’s reactive power is positive. c. Current ahead of the voltage. d. Its power factor is positive.
Problem: Given wye connected source: La Ven Van Von 6-1892 A 6-j802 N 6-j8Q2 I₂ Von = 120-120° V = 120 <-240° bn where V = 1200° an a) Find the line-to-line voltage phasors for the wye connected source. b) Find the line current phasors in each of the three phases of the resistive load. c) Find the current flowing in the neutral.
The figure shows a 3-phase bala Time left 1:06:30 200 /00 Vrms. sequence electrical system. Vcn Vbn %3D al Balanced (-) sequence 100 so a 2000 Vms Select one: O a. 200 /-120 Vrms O b. 200 v2 /0 Vrms O C. 200 /0 Vrms O d. 200 v2/-120 Vrms e. 200/120 Vrms
1. Set up the circuit shown using a function generator for the source voltage Vs. Set the function generator to 10 V P-P at 100 Hz (You need to set the Vp-p on the function generator to 5V). Connect the red lead of the scope to VoUT and the black lead to the ground to measure the output or load voltage. 1N4004 Vout Vs 10Vpp 100HZ 1k Ohm 2. Sketch Vout on right, measure the exact peak voltage to the ground on the oscilloscope (use the oscilloscope). DC coupling setting of the 主 Note: Show the results on the screen to your professor to get the signature. V out (Peak) = Vout 3. What is the measured frequency of the load voltage waveform? Frequency f =
The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is O 6000 VA O 2000 VA O 4000 VA 8000 VA