e thickness of plate. I is 12 mm and plate. 2 is 10 mm. The yield stress an odulus of Elasticity for plate,1 is 300 MPa, and 200 GPa respectively, while f late, 2 is 400 MPa and 210 GPa respectively. Assume the tensile stress is equal e compressive stress for both plates. Calculate the efficiency of riveting system

e thickness of plate. I is 12 mm and plate. 2 is 10 mm. The yield stress an odulus of Elasticity for plate,1 is 300 MPa, and 200 GPa respectively, while f late, 2 is 400 MPa and 210 GPa respectively. Assume the tensile stress is equal e compressive stress for both plates. Calculate the efficiency of riveting system

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.7P: (a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
At a point in a bar of cast iron, the principal stresses are 60 MPa tensile and 120 MPa compressive whereas the third principal stress is zero. Find the factorsof safety based on the elastic limit when the criterion of failure is principal stress theory. Assume the elasticlimit of cast iron is 90 MPa in tension and 440 MPa in compression
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
100 kN A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as shown in Fig. A load of 100 kN is applied to the bracket at an angle of 60° to the horizontal and the line of action of the load passes through the centre of the bot- tom rivet. If the maximum shear stress for the material of the rivet is 70 MPa, find the diameter of rivets. What will be the thickness of the plate if the crushing stress is 100 MPa? 80 80 80 60° All dimensions in mm.
4. A ring made of 2-5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile and compressive stresses in the material of the ring. The mean radius of the ring in 15 cm.
A tube from aluminium with an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what is the maximum force (in kN) that the member can support.
Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 RN tensile load if the diameter become 12 mm find 1. True stress. 2. The length of the rod after deformation.
A circular solid piece of rock is tested in a compression testing rig to examine its stress/strain behavior. The sample is 6 inches in diameter and 12 inches in length, with the compression load cell imposing a constant load of 10000 lbf equally at both the top and bottom of the rock sample. Assuming a measured reduction in length of 0.02 inches, find the compressive stress and strain of the rock.