e In the four-bar linkage system shown, let the circular guide with center at O be fixed such that, when 0 = 0°, the bars AB and BC are vertical and horizontal, respectively. In addition, let R=2 ft, L = 3 ft, and H=3.5 ft. When 0 = 37°, B= 25.07°, y = 78.71°, and the collar is sliding clockwise with a speed vc= 24 ft/s. Determine the angular velocities of the bars AB and BC. (Round the final answers to four decimal places. Include a minus sign if necessary.) R H J The angular velocity of the bar AB is The angular velocity of the bar BC is k rad/s. k rad/s.

e In the four-bar linkage system shown, let the circular guide with center at O be fixed such that, when 0 = 0°, the bars AB and BC are vertical and horizontal, respectively. In addition, let R=2 ft, L = 3 ft, and H=3.5 ft. When 0 = 37°, B= 25.07°, y = 78.71°, and the collar is sliding clockwise with a speed vc= 24 ft/s. Determine the angular velocities of the bars AB and BC. (Round the final answers to four decimal places. Include a minus sign if necessary.) R H J The angular velocity of the bar AB is The angular velocity of the bar BC is k rad/s. k rad/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Exactly one turn of a flexible rope with mass m is wrapped around a uniform cylinder with mass M and radius R. The cylinder rotates without friction about a horizontal axle along the cylinder axis. One end of the rope is attached to the cylinder. The cylinder starts with angular speed v0 . After one revolution of the cylinder the rope has unwrapped and, at this instant, hangs vertically down, tangent to the cylinder. Find the angular speed of the cylinder and the linear speed of the lower end of the rope at this time. Ignore the thickness of the rope.
The 544g collar is free to slide on the smooth rod OA. The rod rotates about pin O at constant angular velocity, é. a =en + še, = a = RÔ?e, + RÖe, for a circular path, R = radius 2.1 Use N-T coordinates, draw a FBD and a kinetic diagram to determine the minimum value of é for which the collar will maintain contact with the stop at A throughout the rotation. 2.2 Would friction between the collar and the rod affect your result in 2.1?
A. The mechanism shown is used to feed cartons to a labeling machine. The drive shaft rotates clockwise. The ram weights 1.5 lb and the coefficient of friction between the ram and the machine is 0.2. Gravitational acceleration: g = 386 in/s². The weight of all other links is negligible. The linear ram acceleration is 5378 in/s² (horizontal direction, sense: to the left). 1. Draw the kinematic diagram. 2. For the instant shown, determine the torque required from the drive shaft to operate the ram. 3" -40° Connecting rod Ram
In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC=500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link E (2) (4) A (1) (1)
Problem 2 A load is to be raised 12 ft by the hoisting system shown, developed by ASCE Club students to lift various loads to the ceiling of the Construction Materials Laboratory. Assume gear A is initially at rest, then accelerates uniformly to a speed of 110 rpm in 5 s, and then maintains a constant speed of 110 rpm. Gear A has radius A 4.0 in, gear B has radius B = Drum C rotates with gear B. = 22 in, and drum C has radius rc = 18 in. Determine: (a) the number of revolutions executed by gear A in raising the load, (b) the time required to raise the load to 12 ft. TB B с Load rc
The figure shows a schematic of a simple Watt governor mechanism with the spindle 0102 rotating at an angular velocity w about a vertical axis. The balls at P and S have equal mass. Assume that there is no friction anywhere and all other components are massless and rigid. The vertical distance between the horizontal plane of rotation of the balls and the pivot O₁ is denoted by h. The value of h = 400 mm at a certain w. If w is doubled, the value of h will be mm. (0) g = 9.8 m/s₂ h Spindle O Q Sleeve (QR) Cylindrical Joint R S
4. The figure below shows a bulldozer. Notice that the track on the bulldozer (the tread that wraps around the wheels) is kinematically similar to the conveyor belt in the previous problem. D В E Suppose the person operating the bulldozer knows the distance between the two main wheels on the side of the vehicle. She looks out the window and, with the aid of a stopwatch, notices that the track is moving forward from her perspective at a constant speed v. Furthermore, as the bulldozer drives forward, the track does not slide or skid on the ground. In answering the sub-questions below, use the idea contained in Equation (2) and express answers in terms of basis (ê1, ê2). You may utilize results from Problem 3. (a) Using the terminology in (2), what does the quantity v directly represent? (b) Let C be a point on the track in contact with the ground. What is the velocity of point C as observed by a stationary person on the ground watching the bulldozer? Why? (c) Find the velocity of point…
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s Ccw. And all forces acting. D EA = 0.55" AB - 2.5" AC = 1.0" 0.75" CB = 1.75" CD - 2.05" C 4 E O B 3 °2 60
The ends of rod AB (link 3) are pin connected to slider 2 at A and disk 4 at B. The disc is rolling without sliding on horizontal surface. At the instant when 0 = 50°, the speed of A is VA = 3.5 m/s directed to the right. a) Locate, on the figure, the I. C. R. for the rod AB and for the disk. b) Use the respective I. C. R. to find the angular velocities (@3, w4) of the rod AB and disk, respectively. c) Determine, using the I. C. R, the velocity of the center of the disk (point G). Given: r = 0.2 m L = 0.8 m 0 = 50° VA = 3.5 m/s 3 B G
An automobile driver took a curve too fast. The car spun out of control about its center of gravity (CG) and slid off the road in a northeasterly direction. The friction of the skidding tires provided a 0.25 g linear deceleration. The car rotated at 100 rpm. When the car hit the tree head-on at 30 mph, it took 0.1 sec to come to rest. The force exerted by the 100-lb child on her seatbelt harness as a result of the acceleration just prior to impact is 875 lbf 618 lbf 657 lbf 725 lbf