The figure below shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 6.40 2, and a 2.50-T magnetic field is directed perpendicularly downward, into the page. Let € = 1.20 m.RXXX·x.*XXX*xxX X*Xxx X*XXxxx x* Xxx|x* XX *xXX*FxXx *Binapp(a) Calculate the applied force required to move the bar to the right at a constant speed of 2.30 m/s.N (to the right)(b) At what rate is energy delivered to the resistor?W

Resistor = 6.40 ohmMagnetic field = 2.50TL =1.20m

e figure below shows a top view of bar that can slide on two frictionless rails. The resistor is R = 6.40 12, and 2.50-1 magnetic field is directed perpendicularly downward, into the page. Let x x x x x x Bin XF Fapp x x x x x x x x (a) Calculate the applied force required to move the bar to the right at a constant speed of 2.30 m/s. N (to the right) (b) At what rate is energy delivered to the resistor? W

e figure below shows a top view of bar that can slide on two frictionless rails. The resistor is R = 6.40 12, and 2.50-1 magnetic field is directed perpendicularly downward, into the page. Let x x x x x x Bin XF Fapp x x x x x x x x (a) Calculate the applied force required to move the bar to the right at a constant speed of 2.30 m/s. N (to the right) (b) At what rate is energy delivered to the resistor? W

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter20: Induced Voltages And Inductance

Section: Chapter Questions

Problem 56AP

See similar textbooks

Similar questions

Consider the system pictured in Figure P28.26. A 15.0-cm horizontal wire of mass 15.0 g is placed between two thin, vertical conductors, and a uniform magnetic field acts perpendicular to the page. The wire is free to move vertically without friction on the two vertical conductors. When a 5.00-A current is directed as shown in the figure, the horizontal wire moves upward at constant velocity in the presence of gravity. (a) What forces act on the horizontal wire, and (b) under what condition is the wire able to move upward at constant velocity? (c) Find the magnitude and direction of the minimum magnetic Field required to move the wire at constant speed. (d) What happens if the magnetic field exceeds this minimum value? Figure P28.26
The square armature coil of an alternating current generator has 200 turns and is 20.0 cm on side. When it rotates at 3600 rpm, its peak output voltage is 120 V. (a) Wliat is the frequency' of the output voltage? (b) What is the strength of the magnetic field in which the coil is turning?
(a) A nonferrous screwdriver is being used in a 2.00 T magnetic field. What maximum emf can be induced along its 12.0 cm length when it moves at 6.00 m/s? (b) Is it likely that this emf will have any consequences or even be noticed?
A metal bar of length 25 cm is placed perpendicular to a uniform magnetic field of strength 3 T. (a) Determine the induced emf between the ends of the rod when it is not moving, (b) Determine the emf when the rod is moving perpendicular to its Length and magnetic field with a speed of 50 cm/s.
A square loop whose sides are 6.0-cm long is made with copper wire of radius 1.0 mm. If a magnetic field perpendicular to the loop is changing at a rate of 5.0 mT/s, what is the current in the loop?
Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor, and the circuit is completed by a bar that is free to slide on the rails (Fig. P32.71). A uniform magnetic field of 5.00 T directed out of the page permeates the region, a. What is the magnitude of the force Fp that must be applied so that the bar moves with a constant speed of 1.25 m/s to the right? b. What is the rate at which energy is dissipated through the 2.00- resistor in the circuit?
A uniform magnetic field B=5.44104iT passes through a closed surface with a slanted top as shown in Figure P31.59. a. Given the dimensions and orientation of the closed surface shown, what is the magnetic flux through the slanted top of the surface? b. What is the net magnetic flux through the entire closed surface?
Unreasonable results Frustrated by the small Hall voltage obtained in blood flow measurements, a medical physicist decides to increase the applied magnetic field strength to get a 0.500-V output for blood moving at 30.0 cm/s in a 1.50-cm-diameter vessel. (a) What magnetic field strength is needed? (b) What is unreasonable about this result? (C) Which premise is responsible?
A rectangular coil with resistance R has N turns, each of length and width as shown in Figure P31.36. The coil moves into a uniform magnetic field B with constant velocity v. What are the magnitude and direction of the total magnetic force on the coil (a) as it enters the magnetic field, (b) as it moves within the field, and (c) as it leaves the field?
Sketch a plot of the magnitude of the magnetic field as a function of position r for a coax (Fig. P31.27).
A 0.50-kg copper sheet drops through a uniform horizontal magnetic field of 1.5 T, and it reaches a terminal velocity of 2.0 m's. (a) What is the net map,-, eh: force on the sheet after it reaches terminal velocity? (b) Describe the mechanism responsible for this force, (c) How much power is dissipated as Joule heating while the sheet moves at terminal velocity?