Answered: During drawing process, using the…

During drawing process, using the Ao=5mm2, Af =4 mm2, K=200 MPa and n = 0.20, the average flow stress will be .. , and if using angle of 15 and, p=1.21, p0.08, the drawing stress will be

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: While solving problems using the average normal and average shearstress equations, why is the…

A: While calculating average shear stress, theoretically, the flaws in the system are not taken into…

Q: engineering and true stress strain curves for shear are similar guess

A: Given:

Q: 10 mm diameter holes are to be punched in a steel sheet of 3 mm thickness. Shear strength of the…

A: Given:Shear strength, τ=400 N/mm2diameter of hole, d=10 mmshear on punch, t1=2 mmsheet thickness,…

Q: derive shear and moment equations

Q: Q4. If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress…

A: Given: The initial diameter of the rod, di = 12 mm The final diameter of the rod, df = 10 mm The…

Q: 20. A forging process is shown at the figure below. Calculate the final diameter, if the initial…

Q: What is the area of the tube? What is the total length of the median line? The shearing stress value…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: How is the shear flow, measured?

A: Shear flow: The shear flow in solid mechanics is a terms on multiplication with thickness which…

Q: Do the stress concentrations exist on a shaft?

A: Stress concentration is increase in stress at particular point where stress is more because of hole…

Q: During the rolling process using 50 rev/min, it found that the torque is 22,000 N.m, Calculate the…

A: N( Revolution) = 50 rpm T( Torque) = 22000 Nm Formula for power P =(2πNT) /60

Q: A circular shape blank will be cut of 100+ 10 N mm diameter from a strip of 2.8+ 100 mm with a…

A: given diameter of circular blank to be cut, db=101 mmstrip thickness, t=2.9 mmclearnace, C=0.25…

Q: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to-40mm, t-35mm,…

A: Given Data: The roller radius: R=20 cm=200 mm The original thickness: to=40 mm The final thickness:…

Q: How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?

A: Answer: Maximum allowable shear stress for thick walled cylinders: As, we know that from maximum…

Q: In rolling process, calculate the applied torque in (N.m) when w= 600mm, K = 275 MPa, n = 0.10, %3D…

A: Given Data W=600 mm K=275 MPa n=0.1 ho=35 mm hf=29 mm R=373.3 mm

Q: A hydraulic forging press is capable of exerting a maximum force = 1,000,000 N. A cylindrical…

A: Given data as per question Maximum force = 100000 N diameter=30 mm Height=30 mm K =400 Mpa n =0.2…

Q: Derive the expression of shear plane angle. Draw and mention all corresponding angle required for…

Q: Prove the formula for Hoop stress and longitudinal stress and also explain poisson ratio.

A: Given Data⇒ Hoop Stress Longitudinal Stress Poisson ratio

Q: shear force and the bending mome in the Fig and sketch the shear and 500 N/m

A: GIVEN:

Q: Since both the force that cause Bearing Stress to Normal Stress is perpendicular to the cross…

A: Stress : When a material is subjected to an external influence (Force, moment, Torque etc) a…

Q: Example (H.W.) Rolling factory reduces the thickness of a 75 mm thick plate to 45 mm in one pass.…

Q: What is Shear Stress and explain with example?

Q: Q4. If you have a rod with an initial cross-sectional area of 10 mm, final cross- sectional area is…

A: Given Force, F = 500 N Yield stress = 300 MPa Find Drawing stress

Q: n a wire drawing operation diameter of a steel wire is reduced from 10 mm to 8 mm .The mean flow…

A: Given:Initial diameter of steel wire, Di=10 mmFinal diameter of steel wire, Do=8 mmThe mean flow…

Q: Using the shear formula, how can we check to see that the allowable shear stress is not exceeded?

A: Shear stress acts parallel to the area of cross section of the member. Its magnitude at the outer…

Q: uess wh

A: given: engineering and true stress strain curve for shear are similar guess why

Q: The maximum safe compressive stress in a hardened steel punch is limited to 1 GPa and the punch is…

Q: Does the shear flow vary linearly along with segments that areperpendicular to the direction of…

A: Shear Flow In the real engineering world, the members are made of from composite pats to achieve a…

Q: How can we find the value of shear flow?

A: Shear flow: In the built-up beams, the phenomena of shear flow appear frequently. These beams are…

Q: Illustrate the effect caused by the longitudinal shear stress?

A: In addition to transverse shear stresses the beam also experiences longitudinal shear stress under…

Q: Calculate the shearing force (kN, rounded off to the nearest whole number) needed for a blanking…

A: The shearing force is given by, Fshear=0.7×σu×T×L where, T = sheet thickness = 2.5 mm L = total…

Q: Calculate the blank size of the figure shown and locate bending lines: The thickness of the sheet t…

Q: In hot rolling process, the following data was collected: to=40mm, tF35mm, C=415MPa, m=0.02, w-60cm.…

Q: Derive the formula for the maximum shearing stress due to bending if the the cross section is a…

A: Derive the formula for the maximum shearing stress due to bending

Q: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to-40mm, 1F35mm,…

Q: What is shear strength & how is it calculated?

A: There are no standard values published in the books for the shear strength. In some cases we take 60…

Q: Given Ox = -7Mpa, Oy = 3 Mpa y T = 8 Mpa, calculate the greatest principal stress and the maximum…

Q: Maximum reduction in thickness for one pass in rolling process is Ahmax that can be expressed by Ah…

Q: How can the Maximum In-Plane Shear Stress determined?

A: The expression of the principal stress in a plane is given by,…

Q: An aluminium slab of 750 mm x 80 mm x 36 mm is forged to the thickness of 25 mm. Find the upsetting…

A: Introduction: Upset forgings are created by concentrating material in a specific section of carbon,…

Q: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to=40mm, t-35mm,…

Q: What is the ratio of maximum shear stress to average shear stress for a circular şection?

Q: Using the shear formula, how can we check that the allowable shear stress is not exceeded?

A: given: Using the shear formula, how can we check that the allowable shear stress is not exceeded

Q: Example 11.18. A rod of circular section is subjected to a shearing force on a plane perpendicular…

Q: In order to calculate the shear strain, the angle of twist should be in radian:

A: In the given statement it is asked wheather the unit of angle of twist is radian.

Q: written plz a billet before and after hot forging from an initial size of 2.5 mm x 2.5 mm x 25 mm to…

A: Given Stress = 18 MPa Length, L = 25 mm Find Force, F Work, w

Q: (Engineering and true stress-strain curves for shear are similar. Guess why?

A: Shear Rigidity: Too known as Modulus of Inflexibility, maybe a degree of material resistance…

Question

During drawing process, using
the Ao=5mm2, Af =4 mm2,
K=200 MPa and n = 0.20, the
average flow stress will be
., and if using angle of
15 and, p-1.21, p=0.08, the
..
drawing stress will be

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pls do not solve the question. My question is how can i determine the the stress axis, for instance sigma(x) or sigma (y)? In the question, the Moment (Mz) is causing the holder's y axis to bend. So the normal stress should be sigma(y) = -P/A + MzY/I instead of what the answer has given sigma(x) = -P/A + MzY/I? sigma (x) should be = 0 instead of signma(y). Am i right?
Using the shear formula, how can we check to see that the allowable shear stress is not exceeded?
Find the principal stresses value
0/ During the rolling process, the average flow stress is 20,000 lb/in², etermining the amount of reduction in the cross-sectional area (use n = 0.40 and K = 35,000 lb/in²).
Pls do not solve the question. My question is how can i determine the the stress axis, for instance sigma(x) or sigma (y)? In the question, the Moment (Mz) is causing the holder's y axis to bend. So shouldnt the normal stress be sigma(y) = -P/A + MzY/I instead of what the answer has given sigma(x) = -P/A + MzY/I. sigma (x) should be = 0 instead of signma(y). am i right?
A drawing operation is performed on 3.0 mm stock. The part is a cylindrical cup with height H = 50 mm and inside diameter Dp = 70 mm. Find the required starting blank diameter Db. Do not find the blank diameter. My question is why is the formula for the volume of cup = pi*Dp*h*t + pi*Dp2*t / 4. Are u able to illustrate it in the picture as i had trouble visualizing it A picture of the cylindrical cup is given.
11 The state of stress at a point is given by : 0, = 20, 50 MPa. Calçulate the normal, shear and resultant stresses on a plane whose normal is in- O, = 40, 0, = 60, ty = - 20, tv, = - 40 and t = = - 20, tyz clined at 40° to x-axis and 54° to y-axis.
I can't seem to find the shear stress at point b. Here's my work for reference.
Q4: In Flat Strip Open Forging (FSOF) Process. A strip ingot of length (90.5mm), width (4.75cm), and initial thickness (1.75cm), is open forging to thickness (15mm). The mean flow stress o y 280+110, and friction factor (0.065), Determine the maximum plate pressure and the press capacity at. (1) forging anset. (II) forging end. 96.5mm
Hi, the diameter is 10 mm in my problem, not 15 mm.
• Part A Draw the shear diagram for the baam. Folow the sign convention. Fig.m 1) Clok on "add Vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- You chould not draw an "extra" vertical line at the looation of appled moment. Note 2- Be cure to Indicate the oorreot types of the funotione between the linec, eg. fin your ancwer the type of a funotion Ie "Ilnsar inoressing ciope" for the funotion that actually has linear deoreacing clopa, the ancwer wll be graded as Incorrect Uce the button "ohange cagment" f nsoeccary. 0000 15 kN 10 kN/m 20 kN m 2m 1m No cloments selected v N) 30 20 Im) 20 Add discontinulty ines and seloct segments to add to the canvas Submit dg Aer • Part B Draw the momant diagram for the baam. Follow the sign convention. Cliok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- The ourve you chooce from the drop-down…
Please help me find the correct solution for this METHOD OF SECTIONS problem. Thank you! ASAP!