ductive load due to a bank of induction motors. The heating elements are considered purely resistive (F, = 1), and the induction motors have a lagging power factor of 0.7. If the supply is 1000 V at 60 Hz, deter- mine the capacitive element required to raise the power factor to 0.95. b. Compare the levels of current drawn from the supply.

ductive load due to a bank of induction motors. The heating elements are considered purely resistive (F, = 1), and the induction motors have a lagging power factor of 0.7. If the supply is 1000 V at 60 Hz, deter- mine the capacitive element required to raise the power factor to 0.95. b. Compare the levels of current drawn from the supply.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=200 Volts, Time period is 5 milli seconds and 0 =40 degrees. Vp t = 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms = b) Angular frequency =
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
Suppose we have an ac current flowing through a coil wound on an iron core. Name two mechanisms by which energy is converted to heat in the core material. For each, how is the core material selected to minimize the power loss? How does each power loss depend on the frequency of the ac current?
If two 3-phase induction machines are mechanically coupled with each other. The two machines are supplied by 50 Hz and 60 Hz, respectively. the speed of the combination of both machines will be:
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.5 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 20 milli seconds and =40 degrees. Vp ì = 0
Does Clampor circuit change the peak-to-peak (i.e., rms value)? Justfy
In the circuit given in the figure, T1 thyristor is triggered at 45 degrees and T2 thyristor is triggered at 210 degrees. circuit120 V, 50 Hz sinusoidal AC voltage is applied to its input. a) Draw the graph of the current flowing through the load resistor Ry.b) Find the effective value of the work flow.
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Q3 A three-phase induction motor has the following data: 50 hp and V440 and 50HZ operating at full load with an efficiency of 89% and a power factor of0.85 lagging. Calculate the total apparent power of the capacitors to raise the power factor at full load to 0.95 lagging. What is the value of the capacitors' capacitance for each phase if we connect the capacitors (a) in the form of delta (b) in the form of a star.
Assume that a three-phase 700KW, 50 Hz, 4200V (Line to Line) Wye-connected induction motor has a full-load efficiency (n) of 100% and a lagging power factor of 0.75 and is connected to a feeder. If it is desired to correct the power factor of the load to a lagging power factor of 0.9 by connecting three capacitors (capacitor bank) at the load as shown in the figure a VLL b VLL IL Motor PF KW Lagging CAPACITOR BANK If QC is rating of the capacitor bank in KVAR that should be connected in parallel with motor and if C is the capacitance of each unit if the capacitors are connected in delta, in microfarads Taking two digits after comma, then QC and C will be Select one: O a. QC = 475.12 KVAR &C = 12.63 Microfarad O b. QC = 675.12 KVAR &C = 42.63 Microfarad O. QC = 775.12 KVAR & C = 42.63 Microfarad Od. QC = 575.12 KVAR &C = 32.63 Microfarad O e. QC = 375.12 KVAR & C = 22.63 Microfarad Of. None of these
A 2MVA, 2.3kV three – phase Y – connected alternator operates at rated kVA at a power factor of 80%. The dc armature winding resistance between terminals is 0.08 ohm. The field takes 70 A at 125 V from an exciter equipment. Friction and windage loss is 20kW, iron losses 36kW and stray load losses are 2.0 kW. Calculate the efficiency of the alternator. Assume the effective armature winding resistance is 120% of the DC resistance. a. 94.0 % b. 92.1 % c. 93.2 % d. 89.5 %