Determine the x- and y-coordinates of the centroid of the shaded area. y I I I y = kx1/3 I 0.5 1 Hint: Use a horizontal strip differential area for integration.

Q: 19. Steady-state heat transfer occurs in the composite wall shown in the figure. A thin-foil heater…

A: Given:Surface area of the wall, A=3.6 ft2Thickness of portion 1, L1=2.1 inches=2.112ft=0.175…

Q: To Z 1 2 T₁ 1. 2. 3. 4" Common Brick 1/2" OSB Sheathing 3-1/2" x 1-1/2" (2x4) Yellow Pine Studding…

A: To Find : The heat loss through the wall. Given : The thermal conductivity of materials are, For…

Q: In infinitely long parallel plates, Biot number and Fourier number are 0.2 and (15). Find the…

A:

Q: E  =  C  +  PV/(n – 1)  Where C and n are constant quantities and n = 1.5. The system undergoes an…

A:

Q: 20 kg A TW S B 10 kg PROBLEM 13.19 The system shown, consisting of a 20-kg collar A and a 10-kg…

A:

Q: A large tank (left side), filled with pressurized water, fills another large tank (right side) open…

A:

Q: 16-2 A liquid subcooler as shown in Fig. 16-14 receives liquid ammonia at 30°C and subcools 0.6 kg/s…

A: Given data: Inlet temperature of liquid ammonia = 30°C Inlet mass flow rate of liquid ammonia, min =…

Q: Explain why if e, and e' are unit vectors of two Cartesian coordinate systems and e'i = Qije; then…

A: Suppose we have two Cartesian coordinate systems, denoted by (x,y,z) and (x',y',z'), and let ei and…

Q: 14. A 6-foot-long circular pipe used to transfer hot water has inner and outer diameters of 1 inch…

A: Given That: Inner Diameter = 1 inch outer diameter = 1.25 inch temperature of water = 170 0F Average…

Q: 8.12 (A/B) A circular bar 4 m long with an external radius of 25 mm is solid over half its length…

A: Given data  External radius = 25 mm  Internal radius = 12 mm Torque = 120 N.m Find the maximum shear…

Q: Refer to hoist system arrangement as in Figure Q1(b) and specifications details in Table QI(b). (1)…

A:

Q: A bar of 7-mm in diameter is only allowed to decrease at a maximum of 1.85% of its total length.…

A:

Q: 8.11 (A/B). A composite shaft consists of a steel rod of 75 mm diameter surrounded by a closely…

A:

Q: A friction clutch is to transmit 10 kW at 3000 rpm. It is to be of single plate type with both sides…

A:

Q: This question requires the use of the extracts from the tables of thermodynamic properties supplied.…

A: Given data:- Pressure =6 bar Temperature =350°C To find:- the specific entropy of the steam

Q: 8.14 (B). Calculate the minimum diameter of a solid shaft which is required to transmit 70 kW at 600…

A: According to the given data P=70kW N=600rpm τmax=75MN/m2=75 MPa We need to find  (a) Minimum…

Q: Simplify the following expressions (note that dj is the Kronecker delta, repeated index means…

A: To solve these expressions, use the definition of the Kronecker delta, which is a mathematical…

Q: 2. The figure below shows forces and moments acting on a machine component. Calculate the resultant…

A:

Q: Answer in half an hour I'll give good rating A heat engine produces 200 kJ/s of mechanical power…

A: Given data:   Net work= 20KJ/s and efficiency= 40%     We have to find Heat rejection to the lower…

Q: Question 7: A gas within a piston-cylinder assembly undergoes a three-legged thermodynamic cycle…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: Problem 3- in the system shown, the pulley is frictionless. There is a balance weight at the slider…

A:

Q: 8.4 (A). A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to…

A: According to the given data P=60MW N=150rpm τ=60MN/m2 θ=0.3°=0.3xπ180=0.005235rad L=1m D=300mm…

Q: (a) Determine the reactions at A and E if P = 660 N. The reactions are positive if to the right or…

A:

Q: A 50N weight is swung in a vertical circle at the end of the 1.8m cord. The maximum strength of the…

A: GivenW=50NL=1.8mFs=200N

Q: Define the definition of decibels (dB) scale and support with two (2) reasons why decibels (dB)…

A: Decibel (dB) Scale: Decibels (dB) is a logarithmic scale that is commonly used to express the…

Q: 12.18 WEY The performance characteristics of a certain centrifu- gal pump having a 9-in.-diameter…

A:

Q: Solve please. Should correct A box with a hinged lid B is half full of an organic liquid (density=…

A: Write the given data. ρ=1.71 slugs/ft3Po=0 psigL=2.5 ftW=1 ft

Q: 8.15 (B) A solid shaft of 75 mm diameter and 4 m span supports a flywheel of weight 2.5 kN at a…

A: Given data  Diameter of shaft = 75mm Length of shaft = 4m Weight of flywheel = 2.5 kN  Power = 35 kW…

Q: The beam ABCD are resting on a pin support at A and a roller support at E (as shown below). What are…

A: According to the data provided in the question A loading beam ABCDE is given We need to find…

Q: Problem 5: Draw shear and bending moment diagrams and sketch the qualitative deflected shape for the…

A: Draw the free-body diagrams of AB.

Q: A 0.64 percent Carbon hypoeutectoid plain-carbon steel is slowly cooled from 950 °C to a temperature…

A:

Q: Use the copper silver phase diagram below. 100g of a 40 wt% Cu 60 wt% Ag alloy is made and cooled…

A: To solve this problem, we will use the copper silver phase diagram, which shows the phases of copper…

Q: A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it…

A: To find: (a) The magnitude of the force in cord AB. (b) The magnitude of the force in cord AC. (c)…

Q: Answer the following questions. 1. What are the procedures used to calibrate platform scale? 2. What…

A: Platform scale: Platform scales are used to weigh heavy items and materials in industrial and…

Q: I am not able to see the answers can you please write it in a paper

A:

Q: 8.21 (B). (a) A solid circular steel shaft is subjected to a bending moment of 10 kN m and is…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: You are asked to design a metal hot dog holder for roasting hot dogs over an open campfire. The…

A: To design: The metal hot dog handle. Given: The temperature at the end of handle is Ts=1400°F. The…

Q: 12-83. The W250 x 22 cantilevered beam is made of A-36 steel and is subjected to the loading shown.…

A:

Q: Use the exact values you enter to make later calculations. Consider the following figure.…

A:

Q: Silicon carbide nanowires of diameter D = 15 nm can be grown onto a solid silicon carbide surface by…

A: Given data: Diameter of silicon carbide nanowires (D) = 15 nm = 15×10-9 mThickness of silicon…

Q: A closed, rigid, 0.5 m³ tank is filled with 6.0 kg of water. The initial pressure is p₁ = 20 bar.…

A: Given: The volume of the tank V=0.5 m3 The mass of water m=6 kg The initial pressure p1=20 bar The…

Q: Problem Statement Based on Problem 6-11 from the textbook. The spring has an unstretched length of…

A:

Q: Determine the horizontal and vertical components of the pin reaction at (B) on ABC for frame shown…

A: According to the question, there is a loading structure  we need to find Reaction at point B

Q: 4.2 A closed, rigid tank whose volume is 1.5 m³ contains Refrigerant 134a, initially a two-phase…

A: Given-Information:- Volume, v = 1.5 m3Refrigerant 134-aInitial Temperature, T1 = 6°CFinal…

Q: A spring-loaded device imparts an initial vertical velocity of 58 m/s to a 0.11-kg ball. The drag…

A: Mass m = 0.11 Kg Fd = 0.0021 V2             Initial Velocity V0 =58 m/s     To find out :- Maximum…

Q: A cylindrical Brass specimen 9.5 mm in diameter and 200 mm long subjected to a tensile load. The…

A: According to the given data D=9.5mm L=200mm E=101GPa ν=0.34 δ=0.08mm (a) Maximum tensile load…

Q: Q2/ Find the resultant force for the concurrent coplanar force system, shown in figure 55N BON 120N

A: The angle between the x-axis and the force 120 N is given by, tan A = (1/2) A = tan-1 (1/2) =…

Q: This question requires the use of the extracts from the tables of thermodynamic properties supplied.…

A:

Q: The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1…

A:

Q: 8.6 (A). A hollow low carbon steel shaft is subjected to a torque of 0.25 MN m. If the ratio of…

A: According to the given data T=0.25MN.m τ=70MN/m2 k=1/3=0.333 G=80GM/m2 We need to find  Diameters of…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.