Determine the time required to accelerate a counter shaft of rotating mass 500 kg and radius of gyration 200 mm to the full speed of 250 rpm from rest through a single clutch. The internal and external radii are 125 mm and 200 mm. Take friction coefficient as 0.3 and the spring force as 600 N. Assume that only one side of clutch is effective.

Determine the time required to accelerate a counter shaft of rotating mass 500 kg and radius of gyration 200 mm to the full speed of 250 rpm from rest through a single clutch. The internal and external radii are 125 mm and 200 mm. Take friction coefficient as 0.3 and the spring force as 600 N. Assume that only one side of clutch is effective.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

..A cone clutch with a cone angle of 15° transmits 58 kW at 1300 rpm. The coefficient of friction of linings is 0.11. Determine the axial spring force necessary to engage the clutch in N if the mean diameter of the active conical sections is 250 mm.
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
The arms of a Hartnell governor are of equal length. When the sleeve is in the mid- position, the masses rotate in a circle with a diameter of 150 mm (the arms are vertical in the mid-position). Neglecting friction, the equilibrium speed for this position is 360 rpm. Maximum variation of speed, taking friction into account, is to be 6% of the mid- position speed for a maximum sleeve movement of 30 mm. The sleeve mass is 5 kg and the friction at the sleeve is 35 N. Assuming that the power of the governor is sufficient to overcome the friction by 1% change of speed on each side of the mid-position, find (neglecting obliquity effect of arms), the (i) mass of each rotating ball (ii) spring stiffness (iii) initial compression of the spring
In an engine governor of the Porter type, the upper and lower arms are 200 mm and 250 mm respectively and pivoted on the axis of rotation. The mass of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30° and 40°, find, taking friction into account, range of speed of the governor.
Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner diameter of 125 mm and an outer diameter of 240 mm and the coefficient of friction between mating surfaces is 0.3. It is assumed that shafts of both machines are co-axial and the driving shaft is rotating at a constant speed of 360 rev/min when it is suddenly brought in contact with the driven shaft/machine initially rotating at 35 rev/min. The Moment of Inertia of the driven machine is 21 kgm2. A slippage period of 6.4 sec is observed while the driven machine is brought to the full speed of the driving shaft. Analyse the frictional power transmission and calculate: The magnitude of the torque necessary to cause the described acceleration of the driven shaft : Tdr Nm The driven machine will accelerate at a rate of One possible correct answer is: 5.3178000646702 rad/s/s,while the motor/driving shaft will have an acceleration of One possible correct answer is: 0 rad/s? The normal force…
8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb.
Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner diameter of 125 mm and an outer diameter of 200 mm and the coefficient of friction between mating surfaces is 0.35. It is assumed that shafts of both machines are co-axial and the driving shaft is rotating at a constant speed of 240 rev/min when it is suddenly brought in contact with the driven shaft/machine initially rotating at 20 rev/min. The Moment of Inertia of the driven machine is 21 kgm2. A slippage period of 6.8 sec is observed while the driven machine is brought to the full speed of the driving shaft. Analyse the frictional power transmission and calculate: The magnitude of the torque necessary to cause the described acceleration of the driven shaft :
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take u = 0.42. Assume uniform wear in clutch.
A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is 2.5 m. The effective radius of the driving pulley is r, = 80 mm and it runs at the speed of 550 rpm. The grove angle of pulleys is 25°. The belt has a mass of 0.35 kg/m and the coefficient of friction of 0.3. If the tension in the belt is not to exceed 650 N, calculate the power that can be transmitted by drive.
A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
Q. A centrifugal clutch has 4 shoes which slide radially in a spider keyed to the driving shaft and make contact with the internal cylindrical surface of a rim keyed to the driven shaft. When the clutch is at rest, each shoe is pulled against a stop by a spring so as to leave a radial clearance of 5 mm between the shoe and the rim. The pull exerted by the spring is then 500 N. The mass centre of shoe is 160 mm from the axis of the clutch. If the internal diameter of the rim is. 400 mm, the mass of each shoe is 8 kg, the stiffness of each spring is 50 N/mm and the coefficient of friction between the shoe and the rim is 0.3. Find the power transmitted by the clutch at 500 r.p.m.
8. Figure 7 shows a four-wheel drive car of mass m = 970 kg. The coefficients of friction is H=0.6. Neglect the mass of the tyres. (a) Determine the greatest possible acceleration of the race car so that its front tyres do not kave the ground nor the tyres slip on the track. (b) Determine the corresponding reactions on tyres A and B. (c) From (b) above, recaleulate the coefficient of friction. If it is not same as either the given values Hs or k, then in one sentence, state or explain why the difference in values? h=0.55 m a= 1,82 m b = 2.20 m Figure 7