Determine the surface tension of liquid in contact with air and a glass tube. If the capillary tube diameter 2 mm is dipped in a liquid of specific gravity 0.8, the liquid rises in the tube by 15 mm, making an angle of contact of 25° with the tube.

Determine the surface tension of liquid in contact with air and a glass tube. If the capillary tube diameter 2 mm is dipped in a liquid of specific gravity 0.8, the liquid rises in the tube by 15 mm, making an angle of contact of 25° with the tube.

Name: Determine the surface tension of liquid incontact with air and a glas
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Determine the surface tension of liquid incontact with air and a glass tube. If thecapillary tube diameter 2 mm is dipped in aliquid of specific gravity 0.8, the liquid risesin the tube by 15 mm, making an angle ofcontact of 25° with the tube.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Similar questions

The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
2. The tank shown contains alcohol (SG=D0.78) and covered by a circular plug 1.2 m in diameter. Calculate the hydrostatic force F Am acting on the plug and its center of pressure. 8m 1.2 m 3. The gate as shown is 3 m normal to the page. It keeps the two liquids from mixing with each onough clocuro botween the oil and
Determine the surface tension of liquid is contact with year and a glass tube if the capeearty tube diameter to 2 mm is depend in a liquid of specific gravity 0.8 the liquid risce in the tube by 50 mm making an angle of contact of 25 digree see the tube
In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 2.5 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder
Answer Part A; Also, calculate the location from the bottom of the pool to the center of pressure of the water on wall AB
What force, F, must be applied to the S-shaped gate to keep it closed? The gate is 1 m wide andthe radius of curvature of each part is 1 m. The liquid is water.
The pipe (0-1-2) shown in the …gure is angled upward at 30 and is …lled with water. The distance from (1) to (2) (along the pipe) is 1.2 m. The manometer liquid is mercury. For part (a), the pipe is capped at location (0) so that the water is stationary in the pipe. What would be the value of h in this case? For part (b), the pipe shown is just a section of a much longer pipe, and water is ‡owing upwards from (0) to (1) to (2). If the pressure loss due to friction from location (1) to location(2) is 20 kPa, what is the value of h in this case?
Find the force of oil on the top surface CD of the figure below if the liquid level in the open pipe is reduced by 4.0 ft.
The system in Fig. is used to calculate the pressure p 1in the tank by measuring the 15-cm height of the liquid in the1-mm-diameter tube. The fl uid is at 60 ° C. Calculate thetrue fluid height in the tube and the percentage error due tocapillarity if the fluid is ( a ) water or ( b ) mercury.
A vessel cylindrical in shape and closed at the top and bottom is 300 mm in diameter, 1 m long and contains water up to a depth of 0.8 m. The air above the water surface is at a pressure of 60 kN/m2 . If the vessel is rotated at a speed of 250 r.p.m. about its vertical axis find the pressure head at the bottom of the vessel (i) At the centre, and (ii) At the edge
alith the aid of an appro priate diagram, ex plain.why when a Capillary tube is inserted in a reserveir containing liquid, the Liguid level in the tube will rise or fall and denire an expression for the riselfell.
A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and water is poured in left and right side of tank respectively. Magnitude of horizontal force at centre that should be applied on cylinder so that it does not roll is (for unit length) kN. 64m Oil S=0.7 1.2 m Water S=1 0.7m