a) If a pneumatic cylinder -driven power tool has the following data as shown in Table 1,determine the rate of reciprocation in rpm.Table 1Piston diameter44.5 mmPiston stroke152 mmAir pressure and temperature(at the 687 kPa gauge and 27°Cpneumatic cylinderAvailable flow rate0.05 m³/min (at standard atmosphericconditions of 101 kPa and 20°C)

first of all find out volume flow rate at pneumatic cylinder condition with the help of ideal gas…

Answered: determine the rate of reciprocation in…

Engineering

Mechanical Engineering

determine the rate of reciprocation in rpm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q8 The bore diameter of each cylinder in a three-cylinder two-stroke petrol engine is 14.71 mm and the stroke length for each cylinder piston is 250.25 mm. During engine testing, the engine runs at 300 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 6.8 cm2 and area length of length of 2.6 cm. For a pressure scale of 350 kN/m2 per cm on the indicator diagram, calculate the indicated power developed by the engine. Give your answer in kilowatts (kW) to 2 decimal places. Pressure versus Volume Indicator Diagram (Pressure scale = 350 kN/m² per cm) Peak Pressure Enclosed net area for engine work done m.e.p Diagram length, cm Diagram height, cm
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor?
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor? complete soln tnx.
oblems: 1. A horizontal pipe, 1 ft. in diameter, tapers gradually to 8 in. in diameter. If the flow is 500 cu ft. of water per minute, what is the difference between the pressures at the two sections? Ans. PA - PB = 443.63lb per sq ft 2. Water flows through a horizontal pipe at a velocity of 50 ft. per sec. Owing to the pipe gradually expanding to a larger size, the velocity decreases to 35 ft. per sec. What is the difference between the pressures at two points, one in each size of pipe? Ans. Pg - PA = 1,236. 75 lb per sq ft
21. The following are the results of tests conducted on a centrifugal pump. Negative pressure head in suction pipe close to pump =22 cms of mercur y Pressure he id in delivery pipe close to pump=1'50 kg/cm2 Difference of level between the two gauges 0 50 metres SHP of the electric motor Discharge of the pump * Dianeter of the suction pipe Diameter of the delivery pipe Calculate the overall efficieney of the pump. -32 hp -010 cumeo %3D =20 cma 18 cms (78 17%)
Only answer if you are sure....Answer should be correct upto two decimals A single acting reciprocating pump running at 50 RPM delivers 0.01 metre cube per second the dia of the piston is 200 mm and length is 400 mm . Determine- theoretical discharge of the pump coefficient of discharge , slip and % slip of the pump
A cylinder is configured with a flow control valve to meter-out during extension. The cylinder is a 2" bore and 1" rod. The pump flow rate is 5 gpm with a pressure reducing valve set to 1500 psi. The load is 500 lbs. If the extension speed is to be limited to 10 in/s, what pressure would be measured on the retraction side of the cylinder, during extension? Enter a whole number.Answer: 1,788 ± 10.
What horsepower is supplied to air moving at 20 fpm through a 2 x 3 ft duct under a pressure of 3 in. water gage?
A gear pump has a 80-mm outside diameter, a 55-mm inside diameter, and a 25-mm width. If the actual pump flow rate at 2300 rpm and rated pressure is 140 LPM, calculate the Theoretical Flow Rate, QT (m3/s). (Hint: first calculate the Displacement Volume) Group of answer choices 0.00361 m3/s 0.00233 m3/s 0.00254 m3/s 0.00262 m3/s
Multiple Versions Question: A double acting cylinder has a bore of 107 mm. The rod diameter is 32 mm. It must produce a pushing force of 10.5 KN. The flow rate available in both directions is 0.01 m/min. Note: Number are randomly generated. it is possible to get some huge dimensions. Calculate the system pressure needed. Express your result In Pa. Pa The force with which it pulls, given the same pressure. Express your result In N. The speed on the outstroke. Express your result In m/s. m/s The speed on the instroke. Express your result In m/s m/s The power used on the outstroke. Express your result In watts watts The stroke of the actuator knowing that it takes 1.22 s for the piston to travel back and forth m
For a 6.25-inch Model 4075 pump operated at 1160 rpm, if 450 GPM of water is to be delivered, what will be the estimated pump head in ft? HEAD IN FEET 30 25 0 0 0 10 O 6 ft 7.25" (184mm) 20 7.00" (178mm). 6.75" (171mm). 6.50" (165mm)] 15 6.25" (159mm). 5 O 16 ft O 20 ft O 12 ft aco® L/SEC 5 OT 10 Model 4075 FI & CI Series 15 -6-6 ⁰ dº 20 ANA 888 778 25 REQUIRED NPSH do 1160 RPM November 1, 2010 K ・dº- [M 90 do 30 8800 81 1HP(.75KW) DeJ kin do 60% 35 do 50 Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 45 3HP(2.2KW), 2HP(1 5KW) 5HP(1 1KW)> CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 L 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE NOWONG FEET 15 12 7 6 2 1 NPSH 758 50 5 HEAD IN METERS 45 586888 KPO 60 40 20 10 LO HEAD IN KILOPASCALS
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places