Determine the rate of flow of water through a pipe of diameter 20 cm and length 50 m when one end of the pipe is connected to a tank and other end of pipe is open to the atmosphere. The pipe is horizontal and the height of water in the tank is 4m above the centre of the pipe. Neglect the minor losses and take f = 0.009.

Determine the rate of flow of water through a pipe of diameter 20 cm and length 50 m when one end of the pipe is connected to a tank and other end of pipe is open to the atmosphere. The pipe is horizontal and the height of water in the tank is 4m above the centre of the pipe. Neglect the minor losses and take f = 0.009.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe lengthis 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should bethe different in elevation between the upper and lower levels in order to achieve this pressure? Takethe density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.
The power 395 W is required to transmit 5 x 10-3 m3/s of water. Find the loss of head due to friction in a pipe. The head loss due to friction (in m of water) Answer
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.
1. The discharge flowing down the pipe is 0.03 m³/s and the pressure at 2 is 0.14 kg/cm² greater than at 1. Assuming the losses in the pipe between 1 and 2 is k. Liquid flowing in the pipe is water. kv2 2g' find the value of 20 cm dia 10 cm dia mercury 3 m
A 2-inch copper pipe connection was made from the basement to the second floor in the building. The pressure difference between the basement and the apartment in the building is 250 kPa. Since it is known that the flow of water is 0.7 L/s; a) Calculate how many cm diameter faucet is used in the problem.
59. Consider two rectangular tanks having constant flow areas of A1 and A2. Thetanks are connected at the bottom by a frictionless pipe of diameter d. The firsttank is filled with water up to an elevation h0 from the connecting pipe. We nowopen the isolation valve. a) Show that the time for levels to equalize is given by:
A frustum cone tank is initially filled with water as R 2w shown in figure. After that, the water drains through a hole of radius (r=0.05 m) is located at the bottom of tank. 1- Find the depth of water at any time (y(t)). 2- compute the time required to drain half volume of water in the tank. where R=w w = 2m g = 10 m/s?
Two piezometers (manometers) are placed 1.5m apart in a horizontal plastic pipe as shown in figure. What is the difference in water level (cm) between the two manometers when the flow rate in the pipe is 0.0004 m /s? Fluid in pipe is water. Pipe diameter 2.5 cm. Density=1000 kg/m. Viscosity = 0.001 Pa-s. %3D 0.25 5.74 log 10 Re 09 | Water
The power 486 W is required to transmit 9 x 10-3 m3/s of water. Find the loss of head due to friction in a pipe. The head loss due to friction (in m of water)
... K 3m 3.5m Im 100mmg An open tank in the form of frustum of a cone has 1m diameter at the bottom and 3m at the top as shown. It is 3.5m high and filled with water at the top. A 100mm diameter orifice with C = 0.92 is located at the bottom of the tank. Determine the time to empty the tank
Q2 A Venturi meter with a minimum diameter of 10cm is to be used to measure the flowrate of water through a 15 cm-diameter pipe. Determine the range of the pressure difference indicated by the pressure gage attached to the flow meter if the range of the flowrate is from 3 to 30 L/s, the contraction coefficient is 0.99 0.98, and the flow is ideal.
Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.