Determine the range of P for which the system of two blocks will be in equilibrium. Friction is negligible except for the surface under block B. Tip: Draw the Free Body Diagram Determine force P [Select] 30° P Determine N-force at gound to block B [Select] B 80 N H, = 0.2- Detemine N-force between surfaces of A and B [Select] Determine the N-force between the wall and block A [Select] A 120 N Choices 93.5, 11.15, 32.48, 29.28 300, 400, 100, 200 156.38, 138.56, 142.12, 200 29.68, 69.28, 89.26, 62.89

Determine the range of P for which the system of two blocks will be in equilibrium. Friction is negligible except for the surface under block B. Tip: Draw the Free Body Diagram Determine force P [Select] 30° P Determine N-force at gound to block B [Select] B 80 N H, = 0.2- Detemine N-force between surfaces of A and B [Select] Determine the N-force between the wall and block A [Select] A 120 N Choices 93.5, 11.15, 32.48, 29.28 300, 400, 100, 200 156.38, 138.56, 142.12, 200 29.68, 69.28, 89.26, 62.89

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 150-kg bar ABO is supported by two cables at A and a slider bearing at B. The end of the bar presses against a frictionless surface at O.Findthe tensions in the cables and the contact force at O.
Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest angle 0 for which the assembly will remain at rest. 600 mm 6N 600 mm 8 N A. Technology Druen by fanoation Tips: 6N force and 8N force are acting vertically by gravity at the center of the material. Expose the forces acting between the bars and the wall (F and N) Check which interaction will first impend sliding - then expose if free body diagram from the internal hinge at B. e =? Answer in ° (1-2 Decimals are accepted)
The elevation of the end of the steel beam supported by a concrete floor is adjusted by means of the steel wedges E and F . The base plate CD has been welded to the lower flange of the beam, and the end reaction of the beam is known to be 18 kips. The coefficient of static friction is 0.30 between two steel surfaces and 0.60 between steel and concrete. If the horizontal motion of tin beam is prevented by the force Q . determine (a) the force P required to raise the beam, (b) the corresponding force Q.
3. For the system shown, a. Determine the equivalent force-couple system at the base at C. Express the resultants in vector form. (Hint: This is not a static equilibrium problem) b. Write the reaction forces at C support in vector form 300 N 600 Nm 3m 200 N 4 m. 400 N B 2m 200 N 7m
The steel pipe (G - 75GPA) has an outer diameter of 50mm and an inner diameter of 30mm. It is fixed at A and three torques are applied to it as shown. Solve the rotation of the free end with respect to the fixed end. 200mm 250mm 300mm 30 N-m 20 N.m 80 N-m O 0.000749rad O 0.000674rad O 0.00624rad O 0.00142rad
3. Two forces having a magnitude of 1000 N and 600 N act on the ring. Determine the arigle e between the forces if the resultant force has a magnitude of 1400 N. 600 N 1000 N
The symmetrical beam cross-section shown is loaded by a transverse shear force V 25 kip. Calculate the maximum transverse shear stress acting on the sec- tion. ΝΑ -+-1 in.|-- H V 6 in. 1 in. - 1 in.|-—_ 6 in.
Find a. Reaction at D in mm b. Location Maximum Deflection from D in m c. Maximum Deflection of the beam in mm
Q2) ACED frame is pinned at C and support by two identical wires at A and B. The two wires have modulus of elasticity E=70 GPa, cross sectional area A=250 mm2 and thermal expansion coefficient a=23 x10-6 1/C. a) If P-1000 N, Determine the force in each wire. b) If in addition to the load P, the temperature of two wires raised by 120 C. Determine the force in each wire. c) To what value the temperature will increased in order to make the wire at B slack? 2a D B C unit
The beam AB has a moment of inertia I = 800(106)mm4, and rests on the smooth supports at its ends. A 50 mm in diameter post CD is placed at the center of the beam. If the temperature of the rod is increased by 100 °C, determine the force developed in the rod. The beam and rod are both made of steel for which E = 200 GPa and α = 11.7(10-6) /°C.
Draw the B.M.D. for the following, (EI) is constant. 50kN B 3m 30° A
An 85pound force is applied to the bent plate as shown. a. Take the moment about the center point between A and B. b. Change the moment into a force couple that acts through A and B.