Determine the physical address of the source operand base on the Based Indexed Addressing Mode. The MOV instruction MOV AX, [BX].[1234] [SI] The contents of IP and CS are 0200, and 2AF2 respectively. PA is 32D24 which use to compute DS Also, the contents of BX and SI are 5252, and A620 respectively. Explain by the draw the registers and the logical of the system memory. Note: the content of PA is 95AB and the coding of this instruction is XXXX Activate Windows Go to Singa

Determine the physical address of the source operand base on the Based Indexed Addressing Mode. The MOV instruction MOV AX, [BX].[1234] [SI] The contents of IP and CS are 0200, and 2AF2 respectively. PA is 32D24 which use to compute DS Also, the contents of BX and SI are 5252, and A620 respectively. Explain by the draw the registers and the logical of the system memory. Note: the content of PA is 95AB and the coding of this instruction is XXXX Activate Windows Go to Singa

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter11: Operating Systems

Section: Chapter Questions

Problem 30VE

See similar textbooks

Similar questions

Q2:- (A) Find the phicycal address if (BP) = 0100H , (SI) = 0200H , (SS) = 2000H and a displacement of 10H, of the instruction MOV AL, [BP+SI+10H]. Which the name of Addressing Modes?
Q1: Determine the physical address of the source operand base on the Based Indexed Addressing Mode. The MOV instruction MOV AX, [BX].[16A0] [SI] The contents of IP, CS and DS are 0120, A342p, and 2C60, respectively. Also, the contents of BX and SI are 6752, and C344, respectively. Explain by the draw the registers and the logical of the system memory in the before execution and after execution. Note: the content of PA is 2B7C and the coding of this instruction is XXXX
II. IMPLEMENTATION OF SIMPLE SYSTEMS. Implement the given RTL below using bus connection and tri-state buffers. Assume that the given control signals are mutually exclusive, and all registers are 4-bit wide. You may include additional flip-flop pins if necessary. V: c€ E, DEE W: DEB, E €1 (high) X: DEC, BEC, A€c Y: cEA, E E A Z: AD, B E0 (low)
A microprocessor scans the status of an output I/O device every 20 ms. This is accom- plished by means of a timer alerting the processor every 20 ms. The interface of the device includes two ports: one for status and one for data output. How long does it take to scan and service the device given a clocking rate of 8 MHz? Assume for sim- plicity that all pertinent instruction cycles take 12 clock cycles.
The P2 low nibble value will be moved to the high nibble of 21h. It is not desired to interfere in any way with the values of the other bits of the address P2 and 21h. Write the required program code using displacement and logic commands in the solution field It has to be solved with assembly code using 8051 architecture.
Match segment and offsetregisters and determine their correspondingactual memory location addressed of the following real mode 80286 segment registers given below. Segment Register Effective Address 1. CS = 2010H 2. DS = 2100OH 3. ES = AB80H 4. SS = 1234H 5. DS = B20FH When: a. DI = 2000H d. IP = ABCDH b. BX = 100AH e. BP = 12FFH c. SP = 3A00H Type the address in uppercase. Do not forget to append H to each addresses. 1. EA: 2. EA: 3. EA: 4. EA:
On a typical microprocessor, a distinct I/O address is used to refer to the I/O data reg- isters and a distinct address for the control and status registers in an I/O controller for a given device. Such registers are referred to as ports. In the Intel 8088, two I/O in- struction formats are used. In one format, the 8-bit opcode specifies an I/O operation; this is followed by an 8-bit port address. Other I/O opcodes imply that the port ad- dress is in the 16-bit DX register. How many ports can the 8088 address in each I/O addressing mode? .
is stored in the memory starting 2- The ISR address of interrupt number at address (0039CH). 3- In the instruction: (MOV AL,[3AFH]), data is transferred to 8086Mp over data clock cycles. lines: using 4- In the instruction: (MOVAX,[5BC2H]), data is transferred to 8086Mp over data lines: clock cycles. using
The content of the stack pointer SP is 3560, and the register PC contains the value 2000. The location 2000 contains the two word instruction BSR 2500. Given that the size of the stack frame is 4 bytes, and that each instruction(along with the data it uses) is 4 bytes long, what is the value contained in SP immediately after the BSR instruction is executed? Select one: а. 2500 O b. 3556 O C. None of these choices d. 2004 O e504
Q1:/ Show the contents in hexadecimal of registers PC, AR, DR, AC, IR and SC of the basic computer when an instruction at address 021 in the basic computer has I = 1, an operation code of the ADD instruction, and an address part equal to 051. The memory word at address 051 contains 0083. The memory word at address 083 contains B8F2. The memory word at address 038 contains A837 and the content of AC is A937. Give the answer in a table with six columns, one for each register and a row for each timing signal. (All numbers are in hexadecimal) uipors - ea
Will upvote! Find the memory address of the next instruction executed by the microprocessor, when operated in the real mode, for the following CS:IP and 80286 register combinations: a. DS=2F2E & DX=9D64 b. CS=9F7A & IP=AB27 c. ES=DE21 & DI=D75F d. SS=FF5C & BP=92B8 e. DS=DC67 & CX=2FE8
Problem 1. This problem is about operand modes, in particular about memory addressing using the operand modes described in lecture and the textbook. The following shows the contents of a portion of the program memory (locations Ox10000 through 0x10040), and certain registers. All contents are 64-bit quantities. Address Memory Contents 0x10040 0x10038 0x10030 0x10028 0x10020 0x10018 0x10010 0x10008 0x10000 a. movq (%rdi), %rax b. movq (%rdi,%rsi), %rax 100 0x10040 200 25 0x10028 0x10020 c. movq 8(%rdi, %rcx, 4) %r8 d. movq -8(%rdi,%rsi), rbx 500 0x10018 2 Register Contents %rdi 0x10008 %rsi %rdx %rcx For each of the following instructions, say what value ends up in the destination register. Each instruction starts with the state shown above, i.e., the effects do not accumulate. 0x20 8 4