Determine the net torque (about the red dot) on the massless strut shown below. Use the FOR wherein + is counterclockwise. 5.0 N 4 m A. 28 Nm B. 50 Nm C. 0 Nm D. 11 Nm 6. A. 0 Nm If one were to remove the forces shown on the strut in question #5 and replace them with the following forces, determine the net torque about the red pivot point: Force #1: 4 N, 270° exerted at the red pivot point Force #2: 6 N, 90° exerted at the red pivot point Force #3: 10 N, 0° exerted at the left end Force #4: 7 N, 180° exerted at the right end B. 68 Nm C. 12 Nm D. 17 Nm 7. 5 m 4.0 N Which of the following is the best description of the situation in question #6? A. The system is in rotational equilibrium B. The system is in translational equilibrium C. The system is in complete equilibrium D. The system is not in equilibrium

Determine the net torque (about the red dot) on the massless strut shown below. Use the FOR wherein + is counterclockwise. 5.0 N 4 m A. 28 Nm B. 50 Nm C. 0 Nm D. 11 Nm 6. A. 0 Nm If one were to remove the forces shown on the strut in question #5 and replace them with the following forces, determine the net torque about the red pivot point: Force #1: 4 N, 270° exerted at the red pivot point Force #2: 6 N, 90° exerted at the red pivot point Force #3: 10 N, 0° exerted at the left end Force #4: 7 N, 180° exerted at the right end B. 68 Nm C. 12 Nm D. 17 Nm 7. 5 m 4.0 N Which of the following is the best description of the situation in question #6? A. The system is in rotational equilibrium B. The system is in translational equilibrium C. The system is in complete equilibrium D. The system is not in equilibrium

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 55P: A diver off the high board imparts an initial rotation with his body fully extended before going...

See similar textbooks

Similar questions

There are four forces acting on a pole, A = 10i N, B = 20j N, C = -30j N, D = -40i N. What should be the magnitude of force E that must be exerted on the pole to maintain static equilibrium? Note: i and j are unit vectors a. 24.65 N b. 31.62 N c. 46.20 N d. 52.78 N e. No Answer
A. Find the required F to achieve Net Torque = 0. Assume b = 2a. B. After a design modification, all forces including F stay the same. If new design is basedon b = 1.5a, what will be the net torque after modifications?
F Pivot d The length of the pool cue is 1.5 m. A force of 11 N is applied at an angle 55°, a distance 0.7 meters from the pivot. What is the torque created? Answer to 3 sig figs.
An engineer trying to determine whether or not her crane can lift loads (at the position shown). Her crane has a 5K chassis and 40K counterweght. Assume all other parts of the crane have negligible weight. 5ft Anwwer all questions relative to the rotationpoint How much torque is caused by the chassis? unit v How much torgque is caused by the counterweight? unit v How heavy ofa load would "barely balance" the crane? unit v Could the crane lift the foliowing loads without tipping over? 20x 25K yes or now
The compound beam is pin connected at B. Determine the components of reaction at its supports and the moment applied at A. Neglect its weight and thickness. Match the answers. 4 kN m 2 m 2 m 1. 6.2 2. 6.0 By= kN 3. 12 moment MA kN-m 4. 0 B. = kN 5. 12.4 kN 6. 4.0 7. 4.8 kN 8. 32.5 kN 9. 32.0 10. 33.2
A 35° 1. A force is applied to the control rod AO as shown. Knowing that the length of the rod is 350 mm, compute the moment of the force about point O using a. Vector method: M, =rxF. b. Scalar method: M, = Fd 150 N %3D 70°
A heavy crate needs to be moved. A crane can provide the force F at the mounting point shown. a.) Determine the moment about point A due to the force F. Enter your answer in Cartesian components with units of ft-lbs. Round to 3 significant digits. F = (100 i + 2453) lb A x α α Values for dimensions on the figure are given in the table below. R. Variable Value 39 in 35° a. MA = X F î+ k) ft-lb
F Pivot d The length of the pool cue is 1.5 m. A force of 27 N is applied a distance 0.9 meters from the pivot. What is the torque created? Answer to 3 sig figs.
Myrtle pulled a lever of radius 58 cm with a force of 23.2 N.a. What is the torque if she pulled it at an angle of 90°?b. What is the torque at an angle of 30°?
Determine the magnitude of the pin force at A. Assume W = 750 lb, a = 3.1 ft, b = 2.2 ft, r = 7 in. r W C Answer: A = i a B A D lb b
what is the magnitude of the resultant force acting on the pin and the angle between the resultant force and its x component. refer to the figure shown below. choices are a. R = 83.62 N , angle 6.05 b. R = 143.09 N , angle 9.79 c. R = 63.84 N , angle 3.26 d. R = 103.32 N , angle 7.78 e. R = 123.19 N , angle 8.95
The cord at B suddenly fails. Treat the beam as a uniform slender rod. The beam has a mass of 145 kg. (Figure 1) Part A Determine angular acceleration of the beam. Express your answer using three significant figures. Enter positive value if the angular acceleration is counterclockwise and negative value if the angular acceleration is clockwise. TVo AEO t vec ? a = rad/s? Submit Request Answer Figure 1 of 1 > Part B Determine x and y components of the initial reaction at the pin A using scalar notation. Express your answers using three significant figures separated by a comma. 800 N ΠV ΑΣΦ ? vec Az, Ay = N 2 m 2 m Submit Request Answer fo