Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.

Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
1. A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the maximum shear stress acting on it, if the twist in the shaft is not exceeding 1° in 2 m length of the shaft. Take modulus of rigidity as 102 GPa.
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
The dimensions of a stepped shaft are shown below. The maximum shear stress specification of the material is 67.1 MPa. Calculate the allowable torque for the shaft. r= 2.4 mm 12 mm 15 mm
A solid steel shaft of circular cross-section has diameter 50 mm, length 1,028 mm and shear modulus 79.3 GPa. If the allowable shear stress is 36 MPa and the allowable angle of twist is 1.9°, determine the maximum permissible torque. Give your answer in Nm to 1 decimal place.
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
A solid steel bar with a circular cross-section has diameter 50 mm, length 1.5 m and shear modulus of 80 GPa. If the allowable shear stress is 48 MPa and the allowable angle of twist is 2.0 degrees, then what is the maximum permissible torque? State your answer in Nm to 1 decimal place.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° (degrees) in a 6 m. length when subjected to a torque of 14 kN-m? Use G = 83 kN/ m^2. Convert your answers to mm.
A steel shaft 'A' of diameter 'd' and length 'l' is subjected to a torque T Another shaft 'B' made of aluminium of the same diameter 'd' and length 0.51 is also subjected to the same torque "T'. The shear modulus of steel is 2.5 times the shear modulus of aluminium. The shear stress in the steel shaft is 100 MPa. The shear stress in the aluminium shaft, in MPa, is: (b) 50 (a) 40 (c) 100 (d) 250
Calculate the shaft diameter on rigidity basis if torsional moment is 195000 N-mm, length of shaft is 1000 mm. Permissible angle of twist per meter is 0.6° and take G = 79300 N/mm² O 108.21 mm O 39.33 mm O 6.99 mm O 48.93 mm
A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is 2/3 of the outside diameter and if G = 83 GPa, find the angle of twist in degrees if the shaft is 5 meters long.
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad