4. Determine the compressive force (in Ib) in the bars shown after a temperature rise of 165°F if d = 0.02 in. Round off the finalanswer to five decimal places.LMUse the following data:BronzeAluminumA = 2.3 sq. inA = 2.65 sq. inE = 14993283 psiE = 10502305 psiL= 12.4 inL= 16.2 ina = 11.97 x 10-6/ °Fa = 12.74 x 106/F

Answered: Image /qna-images/answer/8d0e59ed-9022-478f-936d-af9b800585a1.jpg

Determine the compressive force (in Ib) in the bars shown after a temperature rise of 165°F if d = 0.02 in. Round off the final answer to five decimal places. M Use the following data: Bronze Aluminum A = 2.3 sq. in A = 2.65 sq. in E = 14993283 psi E = 10502305 psi L= 12.4 in L= 16.2 in a = 11.97 x 106/ oF a = 12.74 x 106/F

Determine the compressive force (in Ib) in the bars shown after a temperature rise of 165°F if d = 0.02 in. Round off the final answer to five decimal places. M Use the following data: Bronze Aluminum A = 2.3 sq. in A = 2.65 sq. in E = 14993283 psi E = 10502305 psi L= 12.4 in L= 16.2 in a = 11.97 x 106/ oF a = 12.74 x 106/F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee A w24 X55 is used as a beam with a length of 6m. The beam is supported by a bearing plate of 300 mm x 200 mm x 30 mm on the wall having a thickness of 250 mm.Properties: d=598.68mmbf = 177.93 mmtw =10.03mm k=33.34 mmtf = 12.83mmFy = 250 MPaQuestions:1. Determine the design strength for web local yielding.2. Determine the design strength for web crippling.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
PROBLEM 37: A sieel secion havung a Cioss seciion c: 20 mm x 30 mm is subjected to an axial force of 240 KN The steel section has produces a strain of 0.002. If it has a value of Poissons ratio of 0.30.Find the shear modulus a. 76923 MPa b. 73852 MPa C. 78023 MPa d. 80256 MPa
Problem 4.8 The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm². Part A Determine the magnitude P required to displace the roller to the right 0.28 mm. Express your answer to three significant figures and include appropriate units. Di Submit μA P = 0.09224 mm Previous Answers Request Answer ? 0.8 m 0.8 m - 5 kN 0.6 m-
3. The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18M block is attached. Each steel bar has an area of 566 mm^2 and E=200GPa. For the bronze bar, the area is 866 mm^2 and E=83GPA. Find the stresses developed in each bar. Steel L=Im Bronze L=1.6 m Steel L=Im 18 Mg
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
Homework 8: A (20°C) a rigid beam in placed upon the rods shown in figure: 1) Determine the magnitude of uniformly distributed load w (kN/m) so that beam remains horizontal when temperature of steel becomes to (100°C). 2) Find the stress developed in each rod. Steel A, = 1000mm², as = 12 * 10-6 , E, = 200GPA, L = 500mm %3D %3D Aluminum Aal 1500mm2, aal = 23 * 10-6 , Eal = 70GPA, L = 300mm %3| Rigid beam w (kN /m) A C steel Aluminum 3m 3m
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
By internal couple method, what is the maximum stress on the steel side of the transformed section? Consider the beam section shown below. Express your final answer in ksi and use two decimal places. 24" 14 As=3 IN. ² SECTION E (STEEL) = 29 x 10³ K.5.1. E (CONC) = 3.2 x 10³ K.5.1. M = 9 ALLOW. f(STEEL) = 20 K.5.1. ALLOW. f (CONC)= 1.35 K.S.I.
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN