Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 8.84 0+030 7.88 0+060 8.02 0+090 8.33 0+120 7.5 0+150 6.12 0+180 6.4 Use the best method applicable. Round your answer to 3 decimal places.

Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 8.84 0+030 7.88 0+060 8.02 0+090 8.33 0+120 7.5 0+150 6.12 0+180 6.4 Use the best method applicable. Round your answer to 3 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Three reservoirs A, B and C at water levels of 25 m, 12 m and 8 m are connected by a pipe network.…

A: Given: Three reservoirs Pipe diameter Pipe length Friction factor To find: Direction of flow Flow…

Q: A field is in the form of a regular pentagon. The direction of the bounding sides was surveyed with…

A: Given: Regular pentagon field Magnetic Declination = 7.2 degrees Magnetic Bearing of line AB = N 33…

Q: 2. A grad of 1.5% intersects a grade of -2.5% at station 1+080 of elevation 68.94m. If the summit is…

A: Solution-The given values are as follows The grade g1=1.5%The grade g2=-2.5%Station…

Q: Calculate the horizontal distance from the gun to the point where the projectile strikes the ground…

A: Given Velocity of projectile = 180m/sec At an angle = 30⁰ Acceleration due to gravity = 9.81…

Q: 1.7 in 2.5 in 2.7 in T 0.755 in Three wood boards, each 4.3 in. wide, are joined by the…

Q: Determine the vertixal deflection at the point where the 100N-m moment is located.

A: Given, It is given that, the beam is a simy supported beam having a total length of 4m The beam is…

Q: Determine the value of P

Q: B | 0.75 m 2.07m The rigid bar AB of negligible weight is supported by a pin at 0. When the two…

Q: Any material to be sampled shall be visually inspected to determine discernible variations. If this…

A: Option 3 is the correct answer

Q: For items 4-5, consider the following: At the instant shown, drum D rotates at a constant angular…

Q: Problem 2.4 On the basis of isopluvial maps, the 50 years 24 hr maximum rainfall at Bangalore is…

Q: Obtain 0.5 Hr- UH from 2 Hr UH using S-Curve having Base Flow 8.900 cfs and catchment area 6526000…

A: Given: As Base flow is mentioned hence given hydrograph is Flood Hydrograph Time Runoff (cfs)…

Q: 4. Calculate the force exerted on a stationary curved vane that deflects a 0.025-m-diameter stream…

Q: om A. Compute the vertical reaction at A.

Q: 4.0 3.0 12 kPa Sand: m=16 kN/m³ Ø'=32* YSAT 18.81 kN/m3 GWT

Q: A 54-kg pilot flies a jet trainer in a half-vertical loop of 1200-m radius so that the speed of the…

Q: an elevation of 240.600 m. If the maximum allowable rate of change of grade for this curve is 0.15%…

A: Find…

Q: A certain horizontal curve on a 6-lane highway (3 lanes each direction with no median) has a…

Q: Determine the reactions at the supports and then draw the moment diagram.Assume A is fixed. EI is…

Q: Problem 5. (HKS Problem 7.16) For the cases in the figure below, determine the pressure, elevation…

A: Given diagram :

Q: Convert the bearing into azimuth from north. N 20° 20' E

A: given - bearing N 20° 20' E to find - azimuth from north

Q: For the beam subjected to the loadings as shown, determine the following: 52 kN 40 kN/m 2m 4m B 2m C…

A: a. draw the shear and moment diagrams specifying values at all change of loading positions and at…

Q: Draw the Mohr's circle

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: m Number 5 f = 8m alculate the force at member GH 1.859KN T 1.859KN C 1.371kN T 1.371kN C 1 kN D 1…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-section beam is…

Q: Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: Instructions : To draw orthographic projections using third angle projection method, take the view…

Q: Convert the bearing into azimuth from north. § 420 28' F

Q: rom the x direction, provide the front view, top view, and left-side view using the meter line.…

A: The Isometric Front View, side view, and Top view of above drawing is given Below:

Q: .3 m Pa = 1100 kN Ma = 325 kN - m W12 X 106 K₂ = K₂ = 1.0 Ma = 325 kN - m Pa = 1100 kN W12 x 106 w =…

A: From given data: Cm = 1 B1 = 1.04 Below was the explanation.

Q: The force on the triangular plate that is submerged in water as shown below waters surface 6m 4m is…

Q: What will be the pressure head of a point in mm of Hg if pressure head of that point is equal to 63…

Q: Problem Number 2 Using the slope-deflection method, draw the bending moment diagram. 3m B 3m 2EJ 4m…

Q: Using the slope-deflection method, draw the bending moment diagram. Determine the moment at A. B 3m…

Q: load (KN) Elongation (mm) AL S 0.5 d. 1 3-8 7-9 12-9 14-3 15-9 16-9 17-8 19.1 21-2 24-2 26-9 30 32.0…

A: Hey there, As multiple questions are posted in a single picture. As per our guidelines we can only…

Q: Q2) The areas within the underwater contour lines of a reservoir are as follows: Contour (m) 184 182…

Q: Moment Calculations Truss (Application problem on Trusses) FB = 500. lb B Replace the pinned and…

Q: Determine the vertical deviation of the right support relative to the tangent drawn at the left…

A: P = 500N EI = 106 N/m2

Q: Q1: The fibers in a unidirectional lamina have a diameter of 12 µm and weight fraction of 60%. The…

Q: A rectangular beam has a width of 300 mm and an effective depth of 500 mm. It is reinforced with…

A: Answer We are given width b = 300 mm effective depth d = 500 mm Tension side reinforcement As= 4 -32…

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

Q: Need help asap. Water flows in a wide channel at q = 10 m³/s/m and a depth of 1.25 m. If the flow…

Q: Problem 5. (HKS Problem 7.16) For the cases in the figure below, determine the pressure, elevation…

Q: N 1200N 400 mm 150 5 mm tipico 20 mm 25 mm 20 mm (b) 45 mm

Q: What will be the pressure head of a point in mm of Hg it

A: This question is from Fluid mechanics

Q: Looking at the x direction, provide the front view, top view, line. Provide also the given dimension…

Q: Use

Q: Compute the parameters of a simple curve. PI = Sta 1+395.43 | = 43° 39' Arc basis, D = 4° 15'

A: ###Calculation of parameters of simple curve###

Q: Problem 1. Determine the axial forces, shears, and bending moments at points A and B of the…

Q: i) What is the gauge air pressure in the tank at Point 1?

Q: Using the slope-deflection method, draw the bending moment diagram. 3m 3A 4m 20km 2EJ 3€] D

Concept explainers

Boundary Surveys

A boundary survey is a property survey used to measure the perimeter of any property to locate the boundary line. Only after deciding the boundary, the area of a property can be computed. Bases on the area, the land can be subdivided, sold or any building can be constructed on the land. The property corners are first marked with any type of markers, such as rebar, metal survey markers, pipe, or wooden flags, and are then labeled for identification. The markers should be visible from all sides of the property to ensure optimum visibility. Any paint that assures visibility is used to indicate the boundaries in between the corner points. The procedure of delineating property lines must adhere to legal description and guidelines and it is an important part of the land registration system. This type of surveying is also called cadastral surveying.

Question

Determine the area bounded by a straight road and an irregular boundary using the data given below:
STATION
OFFSETS
0+000
8.84
0+030
7.88
0+060
8.02
0+090
8.33
0+120
7.5
0+150
6.12
0+180
6.4
Use the best method applicable.
Round your answer to 3 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 8.89 0+020 6.66 0+040 7 0+060 6.15 0+080 8.58 0+100 6.39 Use the best method applicable. Round your answer to 3 decimal places. Add your answer
Completely fill up the missing data ((marked with “X”) and apply arithmetical check. STA BMa 0+00 0+10 0+17 TP1 0+25.622 0+30.567 0+45.890 0+60.134 0+85 0+90.567 0+112.750 BS 0.987 HI 122.496 2.521 TP2 1.567 121.632 TP3 2.143 120.275 FS 0+115 BMb Note: All Values are in meters 1.991 IFS 1.243 2.750 1.524 3.124 1.789 2.125 2.897 1.890 ELEV 120.895 119.731 120.117 119.746 XxXxXxXxXxX 118.972 120.065 118.132 118.385
A railroad curve has De = 4°00', I = 24°00', and PI station = 35+45.00 ft. Use the chord definition to calculate the requested values. Submit Request Answer ▾ Part G Calculate station PC. Recall that stations are reported in the form A + B. Enter the answer in the form A, B with A expressed as an integer and B expressed in feet to two decimal places. A, B = ΕΠΙ ΑΣΦ | Η vec Submit Request Answer Part H ? ft Calculate station PT. Recall that stations are reported in the form A + B. Enter the answer in the form A, B with A expressed as an integer and B expressed in feet to two decimal places. A, B = ΜΕ ΑΣΦ Η vec Submit Request Answer ? ft
The technical description of a six-corner lot is tabulated in the table below. LINES BEARING DIST LAT DEP DMD DPD ТР-1 15 11 20 3051.74 1-2 33 W 190.30 2-3 33 3 W 300.00 3-4 33 3 W 4-5 89 54 E 302.27 5-6 6. 6-1 W 312.82 a. Plot the given data. b. Calculate the distances of line 3-4 and line 5-6. c. Calculate the area of the lot by DMD.
Q3/ The following is an incomplete page of level book in which (?) indicates missing Entry line. Calculate all the missing entries and complete the page of level book. also give the usual arithmetical checks. Station A B C D E F G CHECK B.S. 3.22 2.405 2.14 I.S. F.S 3.78 1.535 1.515 Σ BS- Σ FS ? Σ BS- Σ FS= 3.46 1.175 0.98 ? ? Rise (+) ? ? ? ? ? ERISE- > FALL ? ERISE-FALL = Fall (-) ? ? ? RL 350 ? ? 350.63 ? ? ? L.RL-F. RL L.RL -F. RL= Remarks BM T.P.1 T.P.2 ?
complete the table please calculat the angles and complete the following table. B« 零方向 Survey Survey Targe Reading Average Value after Average value afer CLR zero station reand face left face right reading CLR zero with multiple rounds * .. .. 00 02 06 180 02 00 51 15 42 231 15 30 54 12 131 311 54 00 D. 182 02 24 02 02 24 02 12 180 02 06 90 03 30 270 24 141 17 00 321 16 54 221 55 42 41 55 30 292 04 0e 92 03 54 90 36 270 36
Please calculate elevations in the stations given in the table and show the arithmetic check. Write your calculations in detail and fill the table. The units of readings in the table are meter (SI system). H.I. Elevation BS FS Station (m)| (m) (m) (m) K 0.702 188.567 1 0.970 | 1.111 2 0.559 0.679 1.744 2.780 4 1.973 1.668 5 1.927 1.788 L 0.888
Question 2 Compute the area (in acres) of the irregular tracts of land. (All distances are in feet) Note that AA is the last two digits of your Z number. A Offset Point B C D E 1+40 2+20 3+40 4+20 5+10 Stationing Offset 23 21 63 63 63
1. Complete the differential level notes shown below, perform the customary arithmetic check, provide a detailed sketch on every instrument set-up, and a detailed solution. BACKSIGHT FORESIGHT STA HI ELEV HAIR RDGS MEAN RDG S HAIR RDGS MEAN RDG S 3.258 BM20 3.015 532.1234 2.833 1.289 3.584 TP, 1.114 3.319 1.002 3.189 5.964 6.647 TP2 5.714 6.556 5.568 6.412 4.845 3.478 TP3 4.602 3.268 4.469 01 0.846 2.298 TP4 0.739 2.048 0.698 1.885 2.222 BM21 2.111 2.000
An area of land is bounded by straight sides in the shape of a five-sided clockwise polygon ABCDEA. A traverse is run around the area and the coordinates of A, B, C, D and E 2) are calculated as follows: Point mE mN A 679.11 775.87 826.93 807.32 1010.75 711.89 D 985.54 487.66 E 802.38 364.91 Calculate the area enclosed by the traverse lines using the 'Cross coordinate method in m?.
According to given figure, x = lxc + Ac (y1 - y)² + 1xw+Axw (Y-Y₂)² x = (53.7 x 106) + 3929(460.6 - 296.66)² + (333 x 106) +9450(296.66 - 228.5)² x = (159.297 +376.903) x 106 x = 536.2 x 106 mm² Now, ly = lyc+lyw ly = (1.61 x 106) + (16.6 + 106) = 18.21 x 106 mm² ly A = 13379 mm² x = 536.2 x 106 mm4 ly = 18.21 x 106 mm 4
Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 5.74 0+020 4.85 0+040 8.69 0+060 7.82 0+080 7.59 0+100 6.44 Use the best method applicable.