Centimuity oquation ofastendy frow.Terriellis problemfontflow of liquid througha hole)Problem:Detemine the absolute pressure at the inlet section of the pump.Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, t=60°C.Static pressure in the tank p.=266,8 mmHg. Wedge resistancecoefficient Sw=1,5, pipe inlet resistance coefficient Çin=0,5, theheight of the oil level in the tank above the pump inlet sectionн-1,2 м, оil 1-12.Hкраннасос

Answered: Image /qna-images/answer/5a0f7eb2-d565-4b9b-9fa3-9c4cca4c084d.jpg

:Determine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, ta=60°C. Static pressure in the tank p=266,8 mmHg. Wedge resistance coefficient Sw=1,5, pipe inlet resistance coefficient Gin=0,5, the height of the oil level in the tank above the pump inlet section H=1,2 M, oil I-12.

:Determine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, ta=60°C. Static pressure in the tank p=266,8 mmHg. Wedge resistance coefficient Sw=1,5, pipe inlet resistance coefficient Gin=0,5, the height of the oil level in the tank above the pump inlet section H=1,2 M, oil I-12.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
Q-- Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
asap
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
4. A pump is used for the pumping of water from Tank A into Tank B in which the height difference between the surface levels of water is 20 m. The pipe diameter is 400 mm and the pipe length is 2500 m, the coefficient of friction is f 0.0025 and the pump works at a speed of 700 rpm. The characteristics of the pump are shown in Table 4 below You are required to: (a) (10 points) Intepret pump characteristic and system characteristic ina graph. (b) (10 points) Calculate the input and output power at the operating point. 0.1 0.2 0.3 0.35 0.4 0.5 15 17 18 16 14 O30 60 SI83.80 45 H. (m) 11 Table 4: Data of the pump from the Manufacturer
What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with pressure of145 ft head?
Data measured during tests of centrifugal pump driven at 3000 rpm are Parameter Inlet, Section 1 Outlet, Section 2 Gage pressure, p (kPa) 90 Elevation above datum, z (m) 10 Average speed offlow,V (m/s) The flow rate is 15 m3 /hr and the torque applied to the pump shaft is 6.5 N.m. The pump efficiency is 75%, and the electric motor efficiency is 85%. Find the electric power required, and the gage pressure at outlet, section 2. Write the pump specific speed in terms of the flow coefficient and the head coefficient.
Plate 30m V, Rx T. Given z Rx = 890 N O = 90° turbine ebticiency = 90% Find the power required %3D Water
A centrifugal pump has a suction pipe with a diameter of 100 mm, and adelivery pipe with a diameter of 75 mm. When discharging 15 L s -1of water, the inlet water pressure recorded is a vacuum of 198 mm Hg. The delivery pressure gauge, placed at 200 mm above the pump inlet, recorded apressure of 0.95 bar. As a reminder:1 bar = 750 mm Hgdensity of water = 1000 kg m -3 Calculate the total head losses, Ht (i.e., the rise in total head) and considering that the measured input power is 3.2 kW, calculate thepump efficiency.
Centrifugal pump has differential pressure 15 bar and use to transport oil between two separators. If the pressure at first separator is 4 bar calculate the pressure at second separator and NPSH. Where: Suction and discharge pipe diameters = 10 inch, Suction pipe length = 16 m, ld Oil level at first separator 3 m2d Oil density=880 kg/m³ P Oil flow rate=0.092 m³/sec e Pipe roughness= 0.045 mm Discharge pipe length = 25 m O Oil level at second separator = 5.5 m2d Oil viscosity = 9.5 x 10³ Pa.s Oil vapor pressure 22.5 kPa d кра 4.5x10²