PLS ANSWER ASAP I NEED IT PLEASE HELP ME T_T Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L beamsupports a live load of "A" kN/m along the beam centerline plus "E" kPa uniformly distributed over theupper slab surface. Assume clear cover 40 mm and "F" diameter stirrups. Use the unit weight of concrete23.60 kN/m3. Round off your initial calculations and final answer by 3 decimal places.Given:L =13width of column =0.6mz =2.3mOver-all depth of beam, h =725mmWidth of beam, b =350mmThickness of slab, t =125mmEffective depth, d =660mmf'c =35MPaYield strength of flexural steel, fy = 414MPaYield strength of stirrups, fyt =275MPaA =7kN/m Thickness of slab, t =125mmEffective depth, d =660mmf'c =35MPаYield strength of flexural steel, fy = 414MPaYield strength of stirrups, fyt =275MPaA =7kN/mE =kPaF =12mma.) Threshold TorsionkN-mb.) Perimeter of centerline of outermost stirrupsmmc.) Area enclosed by centerline of outermost transverse torsional reinforcementsmm2d.) Spacing @critical region (round off by multiples of 10)mme.) Spacing @2.50 m (round off by multiples of 10)mmf.) Minimum transverse reinforcementsmm2g.) Minimum longitudinal reinforcements for torsionmm2h.) Total Longitudinal bars for torsionmm2

Concrete shear reinforcement is designed to resist forces greater than concrete's shear strength. A…

Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L beam supports a live load of "A" kN/m along the beam centerline plus "E" kPa uniformly distributed over the upper slab surface. Assume clear cover 40 mm and "F" diameter stirrups. Use the unit weight of concrete 23.60 kN/m³. Round off your initial calculations and final answer by 3 decimal places.

Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L beam supports a live load of "A" kN/m along the beam centerline plus "E" kPa uniformly distributed over the upper slab surface. Assume clear cover 40 mm and "F" diameter stirrups. Use the unit weight of concrete 23.60 kN/m³. Round off your initial calculations and final answer by 3 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design a section of a concrete beam reinforced for tension only. The beam is simply supported on a span of 6.00 m and carries a load of 18 KN/m. Use Alternate Method of Design with n = 9. f'c = 20.70 MPa, Fy = 275 MPa. Use b = d/2. Write your solutions on clean sheets of bond paper, scan properly and uploaded on or before the due date/time. %3D Note: Clear concrete cover for the beam: 40 mm Clear spacing between rebars: 25 mm (minimum) Minimum bar size to use as per ACI Code: 16 mm diameter Design for flexure only.
The building slab is subjected to four parallel column loadings. Take F₁ = 3 kN, and F₂ = 8 kN. (Figure 1) Figure 12 m 6 kN 12 kN 4 m 16 m F₂ 1 of 1 6m y Part A Determine the magnitude of the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit Part B ΠΑ x, y = Value Request Answer Specify the location (x, y) on the slab of the equivalent resultant force. Enter the x and y coordinates separated by a comma using three significant figures. Units ΑΣΦ vec ? m
Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L beam supports a live load of "A" kN/m along the beam centerline plus "E" kPa uniformly distributed over the upper slab surface. Assume clear cover 40 mm and "F" diameter stirrups. Use the unit weight of concrete 23.60 kN/m³. Round off your initial calculations and final answer by 3 decimal places. Given: L = 13 width of column = 0.6 Z = 2.3 m Over-all depth of beam, h = 725 mm Width of beam, b = 350 mm Thickness of slab, t = 125 mm Effective depth, d = 660 mm f'c = 35 MPа Yield strength of flexural steel, fy 414 MPa Yield strength of stirrups, fyt 275 MPa A = 7 kN/m E = kPa F = 12 mm E E
Problem: Design a section of a concrete beam reinforced for tension only. The beam is simply supported on a span of 6.00 m and carries a load of 18 KN/m. Use Alternate Method of Design with n = 9. f'c = 20.70 MPa, Fy = 275 MPa. Use b = d/2. Write your solutions on clean sheets of bond paper, scan properly and uploaded on or before the due date/time. Note: Clear concrete cover for the beam: 40 mm Clear spacing between rebars: 25 mm (minimum) Minimum bar size to use as per ACI Code: 16 mm diameter Design for flexure only.
1. A simply supported beam 300 mm wide, 500 mm deep and spans 5.7 m supports a service super imposed dead load of 9 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the depth of equivalent rectangular stress block (mm) at ultimate stage. Write your answer in 2 decimal places only. 2. A simply supported beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 7 kN/m and service live load of 6 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
The cross section of a concrete corner column that is loaded uniformly in compression is shown in the figure. A circular pipe chase cut-outof 10 i n. in diameter r tins t he height of t he co \u m n (see figure).(a) Determine the average compression stress crr in the concrete if the load is equal to 3500 kips.(b) Determine the coordinates x and y{of the point where the resultant load must act in order to produce uniform normal stress in the column.
PROBLEM 1: The continuous floor beam ABCD is shown in the figure. It has a 100 mm slab thickness and the beams bxh is 300 mm x 500 mm. Column section is 0.30 m x 0.30 m. Live load = 3.6 KPa Superimposed Dead load = 2.6 KPa Concrete weighs = 24 KN/m3 L = 8 m. S = 2.8 m. 2.8 2.8 Siahs. neglet the live load Reduchon O Compute the positive moment for beam EF. 2.8 M 8 m 8 m 8 m Compute the negative moment at the face of support E Compute the negative moment at F
Reinforce Concrete: A rectangular beam having a width of 300mm has an effective depth of 600mm. Total depth of beam is 680mm. The beam is reinforced with 3 – 32mm rebars at the bottom. Using normal weight concrete and F’c = 27.6MPa, Fy = 415MPa. a. Using detailed calculation, determine the shear strength of concrete subjected to shear and flexure only if it is subjected a factored moment of Mu = 134KN.m which occurs simultaneously with Vu = 223KN. b. If the beam is subjected to a compressive force of 268KN, using simplified calculation, determine the shear strength provided by concrete. c. If the beam is subjected to a compressive force of 270KN, using detailed calculation, determine the shear strength of concrete if Mu = 140KN.m and Vu 240KN.
Calculate the bending stresses in the beam shown in the figure by using the transformed area method; compressive strength of concrete is 3000 psi, n=9 and M=70 k-ft 17 in. 20 in. 3 #9 bars | (4, = 3.00 in.³) 3 in. -12 in.-
TITLE: ANALYSIS OF Reinforced Concrete Beams (SERVICEABILITY REQUIREMENTS). PROBLEM: Check the serviceability requirements in terms of deflections. Assume concrete weighs 23.5 KN/m³, fy = 414 MPa, and f'c = 28 MPa. PLI = 133 kN PLI = 89 kN WDL = 29 KN/m + Selfweight of beam 1.2 m 1.2 m 2.4 m 78 тm 4 - #32 800 тm 722 тm 400 тm COMPUTATION: Required: 1. Check serviceability requirement using 480 (span length) as the allowable. a. Short term deflection b. Long term deflection assuming 50 % of liveload is continuously applied for 4 years.
2. A 300 mm x 400 mm concrete beam has a span of 5.5m. A post tension force of 600 kN was applied at a point 60mm above the bottom of the beam. Assume concrete would not crack in tension. f.=20.7MPA. Unit weight of concrete is 23.5 kN/m3. Compute the following: а. Deflection due to prestressing force of 600 kN. b. Net deflection of the beam immediately after transfer. 60mm 5.5m
PROBLEM 1. Calculate the uniform live load capacity of the reinforced concrete beam in Figure 1 if f.'=20.7 MPa and f, = 276 MPa. The beam also carries a dead load (including the beam weight) equal to 680 N/m. b= 250mm Wu d= 460 mm L= 6 m 3-25mm o bars Beam Section Figure 1