Design the given circuit at IcQ = ½ ICSAT and VCEQ = ½ VCc use VcC = 26 volts, ICSAT = 18 milli ampere, DC beta, B = 100 and Rc = 4RE. %3D %3D %3D %3D %3D Vcc Re Rc RE Note: Put answers on the blanks and also upload your answers as PDF file in the Moodle Final Exam submission link. 1. The value of collector current Q-point (Icq) in amperes is 2. The value of collector to emitter voltage Q-point in volts is 3. The value of emitter resistance (Re) in ohms is

Design the given circuit at IcQ = ½ ICSAT and VCEQ = ½ VCc use VcC = 26 volts, ICSAT = 18 milli ampere, DC beta, B = 100 and Rc = 4RE. %3D %3D %3D %3D %3D Vcc Re Rc RE Note: Put answers on the blanks and also upload your answers as PDF file in the Moodle Final Exam submission link. 1. The value of collector current Q-point (Icq) in amperes is 2. The value of collector to emitter voltage Q-point in volts is 3. The value of emitter resistance (Re) in ohms is

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
G2/.Design Circint as the following peseripton: A- the positive Cycle of the vout signal is 3.2 and Negative cycle is 4-33 (Note: we must used preetical Diodes and vin is lov) 13- the positive cyclep of vout is s.3 ond Negative cycle is (5.4) [Note:consider vin = tovavd we must used Capaetor with praeticul Didde)
Make a forward bias grap using the figure.
a full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35V to a 3.3k ohms load. Determine the minimum value of filter capacitor if the maximum peak-to-peak ripple voltage is to be 0.5V.
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
4. Draw and explain the circuit of a simple AM demodulator using Junction diode ( draw the input and output waveforms )
(2) In the adjacent circuit, the input signal Vin = F15V is a square wave. Draw the output signal as a function of time on both Vin ends of: (a)- load resistance. (b) Di-zener Vz=6V In terms of behavior, the value of the output voltage is fixed on the drawing, bearing in mind that the diode is made of
Q.3 The input, Vs and the output, Vo of a diode circuit (assuming ideal diode) are shown 3 SEEU/SKEU 1063 in Figure A.2. Name an application that can produce output as in Figure A.2 (ii) and draw the circuit. S UTM S UTM UTM UTM S UTM S UTM O UTM 8 UTM UTM S UTM S UTM UTM UTM S UTM UTM MB UTM ot UTM UT S UTM B UTM UTM 8UTM (i) aUTM UT 8 UTM UTM UTM M UTM TM S UTM UTM UT MS UTM or (i) UTM Figure A.2 8 UTM UT TM S UTM
The operating point is also called the . ..... ..... .. Select one: a. Cut off point b. Saturation point c. Quiescent point d. None of the above