Design of a slender column in a nonsway frame. Figure 9.14 shows an elevation view of amultistory concrete frame building, with 1200 mm wide x 300 mm deep beams on all columnlines, carrying two-way slab floors and roof. The clear height of the columns is 3.95 m. Interiorcolumns are tentatively dimensioned at 450 x 450 mm, and exterior columns at 400 x 400 mm.The frame is effectively braced against sway by stair and elevator shafts having concrete wallsthat are monolithic with the floors, located in the building corners (not shown in the figure).The structure will be subjected to vertical dead and live loads. Trial calculations by first-orderanalysis indicate that the pattern of live loading shown in Fig. 9.14, with full load distributionon roof and upper floors and a checkerboard pattern adjacent to column C3, produces maxi-mum moments with single curvature in that column, at nearly maximum axial load. Dead loadsact on all spans. Service load values of dead and live load axial force and moments for thetypical interior column C3 are as follows:Dead loadP = 990 KNM₂ = 3 kN-mM₁ = -3 kN-mLive loadP = 745 KNM₂ 146 kN-mM₁ = 135 kN-mThe column is subjected to double curvature under dead load alone and single curvature underlive load.Design column C3, using the ACI moment magnifier method. Use f= 28 MPa andf, = 420 MPa.6 stories at 4.25 m - 25.5 m65432OVERHOUDING MENYEBAY ARTEGO AKIMISE AEVERJAARSONIER17777ABColumn C3KONEEN LEDEN7777DC5 bays at 7.3 m - 36.5 m7777E7777F

Since the reinforcing has not been selected we have EI = 0.4*Ec*Ig1+βd Ec = Elastic modulus of…

Answered: Design column C3, using the ACI moment…

Engineering

Civil Engineering

Design column C3, using the ACI moment magnifier method. Use f f = 420 MPa. 28 MPa and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The floor system used in a school classroom consists of a 4 in. Reinforced stone concrete slab. Sketch the loading that acts along joints BF and side girder ABCD.
III. A simply-supported rectangular concrete beam with a width of 300mm wide, 600 mm total depth, and 5.8 m long, is needed to accommodate both ceiling height clearance below and the superimposed loads. If f' = 28 Mpa and steel 415 Mpa, fy = 13) what is the allowable resisting moment of the beam without 300 mm stressing the concrete beyond 0.45f"c and steel 0.60f,? Use the transformed area method and rn 8 65 mm 2 #25mm 535 mm 600 mm 14) what is the allowable resisting moment of the beam using the strength design method. 4 #32 mm 65 mm 15) Compare the results of (a) and (b) and comment your observation.
Date: Practice Problem 1 Given the following girder properties: bne lalxA ben Properties A = 11500 mm2 y = 266x106mm* ly = 45x106mm* d. = 350 mm %3D bf = 250 mm F, = 248 MPa Fb = 148 MPa F, = 99 MPa tf = 16 mm tw =10 mm a) Find the Web Shear Capacity b) How much is the horizontal shear capacity (kN) at the neutral axis? c) If the girder was used as an 8-meter-long simple span carries equal concentration dead load, P at every quarter points and a uniform load of 12.2 kN/m, determine the load P based on shear capacity. d) Find the maximum shear stress if it is used as a 8 m beam simply supported at the left end and 2 m from the right end which carries a total uniform load of 45 kN/m.
A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP
3. A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2163 sq. mm at the bottom, and 1232 sq. mm on the top. Take d': 70 mm, fc' = 21 MPa, and fy = 345 MPa. a) What is the value of "a"? %3! %3D 89.792 mm None of the Choices 92.986 mm 86.707 mm 96.288 mm 99.699 mm
Our University wants to construct a signal post near the entrance, for which they are in need of a horizontal structural element with one end fixed and other end is free. That is to be made up of flexible composite material. The maximum allowable load at free end is 750 kN. The length of the horizontal structural element is 1.5 m. The cross section of the beam is a hollow circular section. Outer diameter 260 mm with wall thickness of 10 mm. Find the deflection at the free end and maximum slope in beam by neglecting self-weight of the diving board. Take Young's Modulus as 110 GPa.
Design the T and L beams that are used for a roof system to cover a floor plan dimensions of 26 ft X 60 ft. The floor system consists of 5 in. thick slab supported by T and L beams at the end. Clear span for beams is 25 ft and they are spaced at 14 ft center to center. Live and external dead load on slab are 100 psf and 15 psf respectively. Compressive strength of concrete is 4,000 psi and yield strength of steel is 60,000 psi. Width and thickness are 14 in and 28 in respectively for both T and L beams.
Subject: Reinforced concrete Design- Civil Engineering A rectangular beam has a width of 300mm and an effective depth pf 537.50mm to the centroid of tension steel bars. Tension reinforcements consists of 6-28mm bars in two rows, compression reinforcement consists of 2-22mm bars, fc' = 27.6MPa, fy = 414.7MPa, d'=60mm. The depth of compression block is _mm. Choices: A. 137mm B. 213mm C. 173mm D. 231mm
Situation #2: Given is a rectangular beam having the following parameters; d = 550 mm d' = 63 mm fc' = 35 MPa fy = 415 MPa As' = 975 mm? %3D %3D As = 3265 mm² b = 400 mm %3D %3D Which of the following most nearly 2.1 gives the depth of the compression * ?block إجابتك Which of the following most nearly 2.2 gives the compressive strength of * ?concrete إجابتك Which of the following most nearly 2.3
A rigid building structure has the following particulars: Dimensions: 10 m x 20 mx 16.6 m high Located in an area classified as exposure B. Is neither open nor partially closed. Risk category: I Wind is 120 km/h and acts on the wall with the higher dimension. What is the external wind pressure on the side wall? O a. formula: wind pressure = qGC₂ = (0.613K₁K₂tKalV²) X G X Cp -248 N/m² O b. -896 N/m² O c. -386 N/m² O d. -333 N/m²
OSseatwork No. 1 (Items 2 and 3) Using transformed area, what allowable uniform load can this beam support in addition to its awn weight for an 8.5m simple span? Concrete weight = 2,400 kgim3. fs = 170 MPa, fe = 12.40 Mpa. =8. 100mm 850mm 100man 5- 32mm 550mm
4.1 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = ____?___ mm