Plz answer ASAP. Design a square-tied reinforced concrete column to support the design loadsshown below. Assume that the column must be designed with the reinforcementplaced around the perimeter and y = 0.7. Take fe' = 4,000 psi and fy = 60,000 psi.Use #9 bars for longitudinal steel.a)Pu = 500 kipsMy = 250 ft-kipsFor the column designed, calculate the ACI value for the column capacity loadedin pure axial compression.b)

Design a square-tied reinforced concrete column to support the design loads shown below. Assume that the column must be designed with the reinforcement placed around the perimeter and y = 0.7. Take f' = 4,000 psi and fy = 60,000 psi. Use #9 bars for longitudinal steel. a) Pu = 500 kips M = 250 ft-kips b) For the column designed, calculate the ACI value for the column capacity loaded in pure axial compression.

Design a square-tied reinforced concrete column to support the design loads shown below. Assume that the column must be designed with the reinforcement placed around the perimeter and y = 0.7. Take f' = 4,000 psi and fy = 60,000 psi. Use #9 bars for longitudinal steel. a) Pu = 500 kips M = 250 ft-kips b) For the column designed, calculate the ACI value for the column capacity loaded in pure axial compression.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete column is reinforced using four steelreinforcing rods, each having a diameter of 25 mm.Determine the stress in the concrete and the steel if thecolumn is subjected to an axialload of 1200 kN. Est = 200 GPa,Ec = 25 GPa.
TRIBUTARY METHOD OF LOAD DISTRIBUTION (3) 2. Consider the floor plan shown in Figure. The floor is 100mm thick F-6 @ 6.67' = 40 %3D C4 I- reinforced concrete. Determine the B2 GI B3 following: (a) load that acts on floor beam B1, (b) load that acts on beam B5, (c) the load acting on corner column C1, and (d) the load acting on interior B4 2 @ 10' = 20' B) C2 I- B5 –I- I G4 G2 G3 B1 5 @ 8'= 40' column C2 ©-I- C3 Ci 40' 20 *Neglect the weight of joists
A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 10-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. Use f’c = 21 MPa and fy = 420 MPa. Determine the nominal axial strength (kN) of the column as per NSCP 2015. Determine the required spacing (mm) of laterial ties 10-mm-dia. Determine the location of the plastic centroid (mm) measured from one short edge.
Situation #3: Given is a rectangular beam having the following parameters; d = 490 mm d' = 60 mm b = 300 mm fc' = 27.6 MPa fy = 276 MPa Mu = 620 kN.m %3D 10 نقاط Compute for the required steel 3.1 area in the compression side إجابتك ibäi 12 Compute for the required steel 3.2 * area in the tension side
A short rectangular column 500 mm on one side and 600 mm on the other side. It is reinforced with 10-28-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. The centroid of the bars are 76 mm from the concrete surface. Use f'c= 21MPa and fy= 415 MPa 1. Calculate the distance of the neutral axis from the concrete compression fiber at an ultimate stage when the column is bent about the axis parallel to the short dimension at a balanced conditioned. a. 309mm b. 358mm c. 364 mm d. 475mm 2. Determine the nominal axial strength of the column for the given condition a. 5.21MN b. 4.56MN c. 3.43MN d. 2.34 MN Please provide complete soln Thank you!
REINFORCED CONCRETE DESIGN (ULTIMATE STENGTH DESIGN) Use fy = 60000 psi (414 MPa) and f'c = 4000 psi (27.6 MPa). Determine the following for each given illustration: a. Depth of compression block b. Depth of neutral axis C. Reduction factor d. Nominal Moment Capacity e. Ultimate Moment Capacity 2 #8 5 in. 3 in. 28 in. 2 #8 5 in. | 15/in. 20 in. 2 in.
PROBLEM 1 A reinforced concrete beam has a width of 250mm and a total depth of 450mm. It is reinforced with a total steel area of 1875sq.mm placed at an effective depth of 375mm. Assume f'c = 27.6 MPa and fy = 414.7 MPa. Discuss and determine the following: (a) Depth of the compression block (b) Moment capacity reduction factor, (c) B₁ (d) Mn and Mu (e) Safe uniform live load that the beam could carry in addition to a uniform dead load of 20 kN/m if the beam span is 6.0m. PROBLEM 2 A T-beam (internal) for a floor system has a slab thickness of 100mm and a total depth of 550mm. It has a web thickness of 300mm. The T-beam is casted monolithically with the slab. The beam has a simple span of 6.0m with a spacing of 2.4m center to center. The beam carries a live load moment of 163 kN.m and a dead load moment of 84 kN.m. Assume f'c = 20.7 MPa and fy = 413.7 MPa. Assume steel covering to the centroid of the reinforcement is 65mm. Determine the following and discuss your solution: (a)…
1. If column AB is made from high strength pre-cast concrete and reinforced with four 20 mm diameter A-36 steel rods, determine the maximum allowable floor loadings P. The allowable normal stress for the high strength concrete and the steel are (Gallow)con 18 MPa and (Gallow)st = 170 MPa, respectively. = 3 m P. P B 225 mm 225 mm Section a-a
A rectangular concrete beam having a width of 450 mm has a total depth of 575 mm. It isreinforced for tension having a steel area of 3200 mm2 and steel area for compression equalto 900 mm2. The compression bars are placed at a distance of 62.5 mm from the top of thebeam while tension bars are placed 75 mm from the bottom of the beam. Use f’c = 21 MPaand fy = 345 MPa. Find the following: a. The location of the neutral axis from the extreme compression fiber, in mm b. The actual stress of the compression bars, in MPa c. The ultimate moment capacity of the beam, in kN.m
Pa max b) A, = 1056 mm? 2. Calculate the ultimate capacity of a rectangular beam with b-350mm, d-540mm, A, =5- 25 mm. Assume fc-24 MPa, fy-345 MPa. use NSCP 2015 ANSWERS: OM, max = 366.2 kN. m 3. A reinforced concrete beam has the following properties:
1. A rectangular beam has b = 300mm, d = 500mm, As = 6 – 32mm diameter bars, fc' = 27.6 MPa, fy = 414 MPa. Calculate: a) depth of compression block, "a" b) fs c) + d) Mu
The column is reinforced with 10 32-mm bars distributed around the perimeter. Load Pn will be applied with eccentricity e about the strong axis. Material strengths are fe = 34 MPa and fy = 415 MPa. The neutral axis c = 360 mm from extreme concrete in compression. Determine the nominal column load and its eccentricity. Find also the ultimate column strength Pn. 15 CODE 350 mm 67 680 mm e 67 Pn T Pr