Design A shunt- type ohmmeter has a moving- coil of internal resistance 60, with a full scale deflection current of 10 mA. The instrument is provide with a battery of 4.3 V.For full- scale deflection, find the value of Rx and R1. If the pointer is rest at the midpoint of the scale, calculate the value of Rx.

Design A shunt- type ohmmeter has a moving- coil of internal resistance 60, with a full scale deflection current of 10 mA. The instrument is provide with a battery of 4.3 V.For full- scale deflection, find the value of Rx and R1. If the pointer is rest at the midpoint of the scale, calculate the value of Rx.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
In the circuit, R=3k ohm , RR= 300 ohm. What is the Va voltage. After you make solution make resolution for every diode and controle their reel situation. (Vd=0,7)
Design a circuit that exhibits the input/output characteristic shown in fgure. Using diodes (Si, Vp = 0.7 V), resistors and other components construct the circuit. Vout (V) m=0.5 3 V Vin (V) -4 V 3 V m=0.6 -4 V
Q2 (a) Figure Q2(a) shows a clipper circuit made with a gemanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10N and RL=1 kN. (i) Sketch the full cycle of input voltage, Vin(t) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. R. Vin Si Ge R VOUT Vpc Figure Q2(a)
Design a clamper to perform the function indicated in the figure Vo +30 V Ideal diodes 20 V Vi Design Vo -10 V -20 V
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
B) For the circuit shown in Figure 5, sketch the output voltage V, for the input V.. D, is an ideal diode. Explain your answer. Note that you do NOT need components' values to solve this problem. 30 v Vo Vi -5 v
Moving to another question will save this response. Quèstion 5 As we change the load resistance supplied through a diode, the operating point of the diode changes. O True False A Moving to another question will save this response. a Cop 近

Analyze the following circuit and calculate the final current that passes through the diodes R1 D1- 5kQ: D2 R2: 15kQ: V1 @Ge. -15V V2 -5V
Half-wave rectifier loaded with R-L is fed with a 120 VAA 60 Hz source. 10 Ω loadFind the inductance value that limits the average load current to 5A for the resistance.
100nF Input Voltage AC Voltage 1MQ capacitor 5V diode 1N4001 -5 3V At which voltage value will the axis of the output voltage settle? а) Ov b) -8V c) +8V d) -3V What is the peak to peak value of the output voltage? a) -13V b) -8V c) +3V d) 10v What is the appropriate name for this circuit? a) biased positive clamper b) biased negative clamper c) positive clamper d) negative clamper If the diode is positioned in the opposite direction, what type of circuit will the result be? a) biased positive clamper b) biased negative clamper c) positive clamper d) negative clamper
a/ What is the function of the inductance L in a single phase halfwave thyristor? b/ A controlled full wave bridge rectifier has a source of 50 Sinwt with R = 10 and L = 20 mH find the d.c load current if a = 40°, then draw Vo and lo use 50 Hz freq. and B = 1.1n %3D