describe the short term behavior of the lightbulbs.
Q: Describe two advantages of transmitting electrical power at high voltages.
A: The explanation of advantages is as follows.
Q: Q3-Compare in a full comparison discussion (with the necessary equations) between Fading effect and…
A: Below find the solution !!
Q: 6. What are the features of LEDS over conventional bulbs? Name some applications for LEDS.
A: features of LED over conventional bulbs :- LED consume less power compared to conventional bulb .…
Q: . Discuss the types of oil circuit breakers.
A: According to the question we have to explain oil circuit breaker types.
Q: How we can classify optical fibers
A: Optical fiber is cable used for communication. It is made up with glass or plastic. It can transmit…
Q: For which measurement is this oscilloscope time difference reading useful?
A: Let the time difference between two waveform is "t" seconds and time period of both the waveform or…
Q: Describe about the smoke alarm experiment.
A: Smoke detectors are used to detect the smoke. When there is a fire and smoke arises, then these…
Q: what is the standing wave of a 75 ohm connected to 50 ohm transmission line?
A: The characteristic impedance is Z0=50 ohms. The load impedance is, ZL=75 ohms The standing wave…
Q: What are the main sources of electromagnetic interference (EMI) that can affect electronic systems?…
A:
Q: What is the unit of Luminous flux, Illumination, Solid angle, Luminance and Lamp efficiency ??
A: When light falls on any surface this phenomena is called as Illumination. Where Light is the cause…
Q: Draw the block diagram of a solar Photo-Voltaic system with the stand by diesel generator and…
A:
Q: What is DF04m? How to use in lighting dimmer system?
A: DF04m is a single-phase bridge rectifier. It has 4 pins having a peak reverse voltage of 400 V and a…
Q: How to wire 220volt ac at a breaker box?
A: To wire 220 V ac at a breaker box, the following steps needs to be followed: Turn off the main…
Q: Discuss the mechanism of incandescent bulb, fluorescent lamp and LED
A: (1) Incandescent Lamp The incandescent lamp works on the principle of heating effect of the…
Q: 2. Discuss any two types of the lightning arresters.
A: The two types of lightning arrester are: Rod Gap Arrester This type of arrester is simple in…
Q: Questions: [1] What are the applications of LED?
A: Solution : LED = Light Emitting Diode Generally LED's are formed by the direct band gap…
Q: Name the instrument used to measure solar intensity??
A: In this question we need to answer which instrument is used to measure solar intensity .
Q: Describe the graph of the oscilloscope
A: Electrical devices are used for measuring electrical parameters. Current, voltage, and power are…
Q: Explain the differences & relationship between fuses and circuit breaker in an electrical system.
A: Fuse- Fuse is used for the safety purpose of home equipment. It operates the over-current protection…
Q: A LED which bright
A: Diode- When diode is forward biased it is short circuited in a circuit ideally. When diode is…
Q: Write the report on “Increase of fluorescent lamp and power factor”
A: Fluorescent lamps: Fluorescent lamps, often known as fluorescent tubes, are low-pressure…
Q: Draw the cross sectional view (Diagram) of flat plate solar collector and name all the parts?…
A: Solar collector is used to store sun's heat energy and then convert the energy into another energy…
Q: Which materials are used in manufacturing of LEDs?
A: A Brief About LEDs Light Emitting Diode is referred as LED which is made up of semi-conductor which…
Q: e reflection coefficients
A: Reflection- When light wave passes through interface diagonally between two media if it gets…
Q: How
A:
Q: Name and explain the basic techniques used to couple light from an LED into an optical fiber.
A: The basic techniques used to coupling light from an LED into an optical fiber is shown below: The…
Q: are the main region 3 what enside System verilog simulation in time step?
A: Verilog is Hardware Description language . The memory and array declaration in Verilog is static in…
Q: Q12. Which materials are used in manufacturing of LEDS?
A: A Brief About LEDs Light Emitting Diode is referred as LED which is made up of…
Q: Why are the light sources used in high end optic fiber networks either laser or LEDs? Why would it…
A:
Q: The minimum value of current at which the fuse element melts is called?
A: The minimum value of current at which the fuse element melts
Q: What quantity does a phototransistor measure or sense
A: This question is about an optical electronic component called phototransistor. Basically it's a…
Q: Is the laser beam brighter than the sun? Yes No Probably
A: The answer of the above question is 'Yes'. The explanation is given in the next step.
Q: Which microelectronic device failure mode is the most important for systems which must operate for…
A: In this case, the reason, which causes microelectronic devices to fail, needs to be selected.
Q: What electronic component is often used to prevent large voltage spikes from being produced when the…
A: When the current flowing through the inductor suddenly terminated then a large voltage spike may…
Q: a. What is meant by transmittive cell type in LCD construction
A: According to guidelines we need to solve only the first question. According to the question, we need…
Q: Explain about air blast circuit breakers and write the advantage and disadvantages of the same?
A:
Q: Describe at least 5 equipment’s used in Microwave measurement set up. 2. Describe two useful…
A: In microwave measurement set up conventional instrument like voltmeter and ammeter won't work due to…
Q: Sketch and explain the working operation of a Dish type solar cooker?
A: HI there, as the two questions posted are not related to each other, we shall answer part 1 of the…
Q: Draw the energy band structure of a conductor and a semiconductor material.
A:
Q: A three-way bulb works with a switch that has settings for off, low, medium, and high. What mod…
A: A three-way lamp, also known as a tri-light, is a lamp that uses a 3-way light bulb to produce three…
Q: What is bta16? and how used in lighting dimmer system
A: It is a three-pin TRIAC, it is used for the ac control switching applications. For fast switching…
Q: How does TP4056 works? What is the purpose of red and blue lights in the components?
A: The TP4056 chip is a single-cell lithium-ion battery charger that protects the cell against…
Q: can I use a USB port for power supply in DIY oscilloscope?
A: An Oscilloscope is a electronic device which is used for display of various electrical fields. It…
Q: What is the working explanartion for full-smd 16-led board?
A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…
Q: 3. Which factor determines the color of the emitted light of the LED?
A: The explanation is as follows.
Q: Prepare an assembly chart for a table lamp.
A: An assembly chart is model that shows which part are to be fitted together and the overall view of…
.jpg)
Step by step
Solved in 2 steps with 2 images
- A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.İf the effective voltage value is 80 volts and the effective current value is 4A in the series RLC circuit in the figure, what is the capacitance of the capacitor?
- I am having trouble with this problem it might be the dot notation for the inductors but I am not entierly sure that is the only issue I am havingWith V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 HzConvert the circuit from a T to a pi configuration
- An RL series circuit is connected to a 240 volt 60 hz line the capacitor has current of 1.25 amperes flowling though it. the Xc of the inductor is 22 ohms. the resistor has a resistance of 16ohms. how much voltage is dropped across the resistor?What is the derivation of bilinear switched capacitor resistorM EXPERIMENT 01 V(n002) V(n001) 10V- 8V- 6V- 4V- 2V- OV- -2V- 4V- -6V- -8V- -10V- 0.00ms 30.00ms 60.00ms 90.00ms 120.00ms 150.00ms 180.00ms K EXPERIMENT 01 X Diode 1N914 V Resistor SINE(0 10 60000 100) 10K .tran 2
- If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10Problem: 25 mH m Find Leq In below figure. 10 mH m 60 mH m 20 mH m 30 mH m -o b L 0000Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 6.946 ohms R2 = 9 485 ohms C1 - 0.731 Farad C2 - 0.925 Farad Vs - 15 Volts Frequency = 168 Hz What is the Capacitive Reactance of C1?